ODM Rocker v1.01 discussion

[Dimortal]

Do You Have Infinity Box ?

[Dimortal]

I Connected Panasonic X60 To Infinity Box Connected To W375 And Opened ODM 1.01.
Selected The Com Port That Infinity Used.
That's How I Did A Full Backup Of W375.
I Yet Have To Try To Unlock An Easy Model C Series Or Something.....

Try And Post.

[Dimortal]

Also Try X70 As Well (Prefer This One)

[ExTrEmE]

Nope i dont got infinity box. do you know if there is another bos that is compatible with the ODM software or something? I tried with JAF box but it didnt really work out hehe


hmm do you think if i buy a SETOOL3 box and use the box for the ODM cable will it work?

[orbita]

Nope i dont got infinity box. do you know if there is another bos that is compatible with the ODM software or something? I tried with JAF box but it didnt really work out hehe


hmm do you think if i buy a SETOOL3 box and use the box for the ODM cable will it work?

infinity in this moment can't help with new calipso+ models.
same unlock problem.
with prolific cable and new odm rocker conect work good.
bug with conection solved and software work very good.
search for sst cable.
this cable is prolific based,have low cost and have rj45 conector.
so..,upgrade for other phone models not problem with this cable.
tested and work good with ultima and odm rocker.
with ftdi cable exist some conection problem.
but after make connect this cable work good too.
infinity,setool box use ftdi ic.

[vermsky]

@ORBITA

I honestly couldn't understand the freaking schematic Can you please just take that pic and tell me where RX, TX and Ground should be.

Thanks.

[orbita]

sure.
here is conector
r=tx,l=tx
tx meens transmited,rx meens reseived signal.
now,what cable(ft232bm or pl2303) you have?

[vermsky]

sure.
here is conector
r=tx,l=tx
tx meens transmited,rx meens reseived signal.
now,what cable(ft232bm or pl2303) you have?

for fighter cable. the same one i posted a while ago.

[orbita]

ok,you will have problem with conection,but ....
here you can read more about this ic.
USB-1 : USB-to-serial interface kit
24,25 and gnd need conected to cable.
figter is based with same ic.

[ExTrEmE]

im trying to make a cable i just need to make a female RJ45 port and then solder the ODM blue,black,white cables to the RJ45 jack. I got the instructions from unlockcellular i just need to get the Female jack and im done. Also im going to try the V600 headset will that be fine? but the wires i found was RED BLACK and GOLD so i dont know if it will work. Even though i will just cut the original cable

[vermsky]

im trying to make a cable i just need to make a female RJ45 port and then solder the ODM blue,black,white cables to the RJ45 jack. I got the instructions from unlockcellular i just need to get the Female jack and im done. Also im going to try the V600 headset will that be fine? but the wires i found was RED BLACK and GOLD so i dont know if it will work. Even though i will just cut the original cable

can you send those instructions to me too?

[orbita]

i'am write about all this.
siemens data cable use prolific ic.
in my country cost is @5$.
sst cable cost is @15$
this cable use prolific too and have rj45 conector.
make cable for this conector is very easy.
if not have rj45 conector use serial ports conectors(male/female and all is ok) it's very easy to make.

[orbita]

can you send those instructions to me too?

figter cable schematics is here:
Link
need use pins 1@4 from ps/2 conector.
see c62 pins conector.
it's wery easy.

[ExTrEmE]

I was told to just use the female RJ45 cable so the Motorocker cable can be plugged into the RJ45 port and then connect the ODM cable to the female RJ45 port

[vermsky]

I was told to just use the female RJ45 cable so the Motorocker cable can be plugged into the RJ45 port and then connect the ODM cable to the female RJ45 port

so you're talking about a female to female rj45 right?