Announcement

Collapse
No announcement yet.

Redmi Note 7 (Lavender), wonīt go out of EDL mode.

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Redmi Note 7 (Lavender), wonīt go out of EDL mode.

    Hi everybody, i have a problem with a Redmi Note 7 32gb


    Device Manufacturer : xiaomi
    Build ID : PKQ1.180904.001
    Display Build ID : PKQ1.180904.001
    Release ID : 9
    Device Model : Redmi Note 7
    Device Name : lavender
    Architecture ABI : arm64-v8a
    Architecture ABI List : arm64-v8a,armeabi-v7a,armeabi
    Build Description : lavender-user 9 PKQ1.180904.001 V11.0.4.0.PFGMIXM release-keys

    Phone was perfect but with Xiaomi Account.
    But it didn't allow to flash unlock Bootloader files over usb with a No Auth Loader wich worked for me in the past.
    So I have flashed files over isp with Medusa Pro, wich I regret to do it since it doesn't make resizing gpt very well, so I putted my old Riff v1 into work and adjusted gpt and phone turned on, but it said system destroyed.
    Flashed again over usb this time and phone is now in edl mode, but something weird is happening. now it fail no connect with any firehose loader, no matter if i'm using Riff or any qualcomm flasher, when I try to flash over firehose, it disconnect, and connect again after a few seconds.

    Any help would be apreciated.

    Post Note: I canīt use test points due some idiot in the past disappeared those points.

  • #2
    Open serial port...OK
    Connecting to the RIFF Box...OK
    Firmware Version: 1.54 (RIFFBOX1), JTAG Manager Version: 1.88
    Selected Package: [Xiaomi Redmi Note 7 USB V1.01 by <legija>]

    Connecting to the Device via USB Interface...OK
    Serial Number: [94A74470], MSM H/W ID: [00000000/0008C0E1], PK HASH: [A7B8B82545A98ECA]

    Initializing Communication via Qualcomm Firehose Protocol...ERROR

    ERROR: Default FLASH1 Chip was not Recognized by the DCC Loader. Terminating.

    I can connect emmc throught rj-45 port successfully but not with usb connecion.


    Open serial port...OK
    Connecting to the RIFF Box...OK
    Firmware Version: 1.54 (RIFFBOX1), JTAG Manager Version: 1.88
    Selected Package: [Xiaomi Redmi Note 7 USB V1.01 by <legija>]

    Connecting to the SD/eMMC Card...OK
    Set I/O Voltage reads as 1.80V, SD_CLK Frequency is 2.50 MHz

    Detected eMMC Chip, ID: 0x15/0x00 (DD68MB), User Area Partition = 0x000747C00000 Bytes (29.12 GB)

    Analizing the FullImage File:
    Looking for the MBR Signature ................... FOUND at 0x00000000
    Looking for the GPT Signature ................... FOUND at 0x00000200
    Looking for the PIT Signature ................... NOT FOUND

    Current Phone/Image File is recognized to have the EFI Layout.
    Total quantity of listed partitions: 66

    Initializing Temporary Storage File for User Area Partition...OK

    Analizing partition contents complete.
    Last edited by kosovo37; 07-09-2020, 02:54 AM.

    Comment


    • #3
      Can you attach here those bootloader unlock files ?

      As for next steps, you should flash lavender firmware files over ISP but unselect large partitions (system/userdata/cache/vendor). Adjust gpt afterwards and there should be fastboot/recovery mode.
      I'll check what i have here so possibly we can add bootloader unlock to ISP package.
      ICQ: 299-912-089
      QQ: 1634811353

      Comment


      • #4
        welcom bro taset this file
        Just a moment...
        enter your phon en edl mode
        and wirite last firmware
        Last edited by moh@; 07-09-2020, 02:41 PM.

        Comment


        • #5
          Originally posted by Legija View Post
          Can you attach here those bootloader unlock files ?

          As for next steps, you should flash lavender firmware files over ISP but unselect large partitions (system/userdata/cache/vendor). Adjust gpt afterwards and there should be fastboot/recovery mode.
          I'll check what i have here so possibly we can add bootloader unlock to ISP package.
          Just a moment...

          Here is it.

          The files is tested on several Note 7.

          Comment


          • #6
            Originally posted by moh@ View Post
            welcom bro taset this file
            Just a moment...
            enter your phon en edl mode
            and wirite last firmware
            How to load with Jtag Manager?

            Comment


            • #7
              bro this for concet with usb en edl mode

              Comment


              • #8
                Originally posted by moh@ View Post
                bro this for concet with usb en edl mode

                Open serial port...OK
                Connecting to the RIFF Box...OK
                Firmware Version: 1.54 (RIFFBOX1), JTAG Manager Version: 1.88
                Selected Package: [Redmi Note 7 (lavender) V1.01 by <molop>]

                Connecting to the Device via USB Interface...OK
                Serial Number: [94A74470], MSM H/W ID: [00000000/0008C0E1], PK HASH: [A7B8B82545A98ECA]

                Initializing Communication via Qualcomm Firehose Protocol...ERROR

                ERROR: Default FLASH1 Chip was not Recognized by the DCC Loader. Terminating.

                Could this be caused by a broken clk resistor?

                Comment


                • #9
                  Originally posted by kosovo37 View Post


                  Open serial port...OK
                  Connecting to the RIFF Box...OK
                  Firmware Version: 1.54 (RIFFBOX1), JTAG Manager Version: 1.88
                  Selected Package: [Redmi Note 7 (lavender) V1.01 by <molop>]

                  Connecting to the Device via USB Interface...OK
                  Serial Number: [94A74470], MSM H/W ID: [00000000/0008C0E1], PK HASH: [A7B8B82545A98ECA]

                  Initializing Communication via Qualcomm Firehose Protocol...ERROR

                  ERROR: Default FLASH1 Chip was not Recognized by the DCC Loader. Terminating.

                  Could this be caused by a broken clk resistor?
                  Of course. CLK resistor connects cpu with emmc . . .
                  Value is 24 ohms in most cases, but you could short it.
                  ICQ: 299-912-089
                  QQ: 1634811353

                  Comment

                  Working...
                  X