Meizu M6 pinout or EMMC Dump Need

[otherboy123]

I have scatter firmware when i put firmware software auto close

• Open serial port...OK
• Connecting to the RIFF Box...OK
• Firmware Version: 1.49 (RIFFBOX1), JTAG Manager Version: 1.78
  
• Connecting to the SD/eMMC Card...OK
• Set I/O Voltage reads as 3.24V, SD_CLK Frequency is 727 KHz
  
• Memory Type .......................... eMMC
• Manufacturer ID ...................... 0x45
• OEM/Application ID ................... 0x00
• Product Name ......................... "DF4016"
• Package .............................. BGA
• User Area Partition Size ............. 0x0003AB400000 Bytes (14.68 GB)
• Boot Partition Size .................. 0x000000400000 Bytes (4.00 MB)
• RPMB Partition Size .................. 0x000000400000 Bytes (4.00 MB)
• OCR Register ......................... 0xC0FF8080 (Dual Voltage, High Capacity)
• Write Protection Bits ................ NONE
• ExtCSD Register Fields ............... [177] = 0x00, [179] = 0x40, [162] = 0x01
• Boot Configuration ................... No Boot
• Chip Revision ........................ 0.1
• Multimedia Card Revision ............. 1.8 (UNKNOWN)
• Serial Number ........................ 0x1337D23B
• Memory Manufacturing Date ............ October, 2017

[otherboy123]

Erase EMMC not work or emmc is dead?


Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.49 (RIFFBOX1), JTAG Manager Version: 1.78

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 3.01V, SD_CLK Frequency is 727 KHz

Detected eMMC Chip, ID: 0x45/0x00 (DF4016), User Area Partition = 0x0003AB400000 Bytes (14.68 GB)

Invalid length. It should not be zero.

Imgur: The magic of the Internet

[otherboy123]

Processed MTK Scatter File...OK

Scatter File's Partition <PRELOADER> Cannot be Found in the Current Layout. Cannot Inject its File "preloader_wt6750s_66_s11_n.bin"
Scatter File's Partition <RECOVERY> Cannot be Found in the Current Layout. Cannot Inject its File "recovery.img"
Scatter File's Partition <CUSTOM> Cannot be Found in the Current Layout. Cannot Inject its File "custom.img"
Scatter File's Partition <DEVINFO> Cannot be Found in the Current Layout. Cannot Inject its File "devinfo.bin"
Scatter File's Partition <MD1IMG> Cannot be Found in the Current Layout. Cannot Inject its File "md1rom.img"
Scatter File's Partition <MD1DSP> Cannot be Found in the Current Layout. Cannot Inject its File "md1dsp.img"
Scatter File's Partition <MD1ARM7> Cannot be Found in the Current Layout. Cannot Inject its File "md1arm7.img"
Scatter File's Partition <MD3IMG> Cannot be Found in the Current Layout. Cannot Inject its File "md3rom.img"
Scatter File's Partition <LK> Cannot be Found in the Current Layout. Cannot Inject its File "lk.bin"
Scatter File's Partition <LK2> Cannot be Found in the Current Layout. Cannot Inject its File "lk.bin"
Scatter File's Partition <BOOT> Cannot be Found in the Current Layout. Cannot Inject its File "boot.img"
Scatter File's Partition <LOGO> Cannot be Found in the Current Layout. Cannot Inject its File "logo.bin"
Scatter File's Partition <TEE1> Cannot be Found in the Current Layout. Cannot Inject its File "trustzone.bin"
Scatter File's Partition <TEE2> Cannot be Found in the Current Layout. Cannot Inject its File "trustzone.bin"
Scatter File's Partition <SECRO> Cannot be Found in the Current Layout. Cannot Inject its File "secro.img"
Scatter File's Partition <SYSTEM> Cannot be Found in the Current Layout. Cannot Inject its File "system.img"
Scatter File's Partition <CACHE> Cannot be Found in the Current Layout. Cannot Inject its File "cache.img"
Scatter File's Partition <USERDATA> Cannot be Found in the Current Layout. Cannot Inject its File "userdata.img"

Operation complete. From Scatter File were Loaded 0 partitons. Skipped 18 partitions.FAILED
ERROR: No response from the RIFF Box.
Failed to receive answer to READ command.

[Legija]

Hi,
I'm not sure if You understand how to use eMMC plugin and scatter files.
For this to work, BMTpool partition must be present in phone or external dump. This partition is always located at the end of address space.


--
First, make sure to establish connection properly:


1. Do not connect power source to phone board (battery or USB cable)
2. Make sure to connect all ISP pins properly, and that VCC has sufficient current so it can power eMMC chip circuitry


3. DO NOT try erasing eMMC chip blindly




--
If You have proper connection, start eMMC plugin and click "Load layout from Device". this process can take some time, wait for it to finish and make screenshot, then post here.

[otherboy123]

Meizu M6 pinout or EMMC Dump Need

Can u give me direct ISP PINOUT FOR THIS DEVICE?
This phone have no pertition in scatter I think.
I am old riff user master

I try to erase and write firmware with Easy-Jtag and resoldering emmc to phone same error and dead .
I want direct emmc pinout for this thanks a lot now my emmc is blank no GPT pertation and nothing in there I think


I am removing emmc and connect direct like that Moorc Adapter work fine

[Legija]

Download this file, extract it in same folder where firmware files are located.


In eMMC PLugin, open this file "PGPT.bin" and click "Load layout from file".
After that, click "Load firmware files" and select scatter file.


When process is finished, You'll see this:
Processed MTK Scatter File...OK

Scatter File's Partition <PRELOADER> Cannot be Found in the Current Layout. Cannot Inject its File "preloader_wt6750s_66_s11_n.bin"
Loaded Firmware File: "recovery.img" into partition: <RECOVERY>
Loaded Firmware File: "custom.img" into partition: <CUSTOM>
Loaded Firmware File: "devinfo.bin" into partition: <DEVINFO>
Loaded Firmware File: "md1rom.img" into partition: <MD1IMG>
Loaded Firmware File: "md1dsp.img" into partition: <MD1DSP>
Loaded Firmware File: "md1arm7.img" into partition: <MD1ARM7>
Loaded Firmware File: "md3rom.img" into partition: <MD3IMG>
Loaded Firmware File: "lk.bin" into partition: <LK>
Loaded Firmware File: "lk.bin" into partition: <LK2>
Loaded Firmware File: "boot.img" into partition: <BOOT>
Loaded Firmware File: "logo.bin" into partition: <LOGO>
Loaded Firmware File: "trustzone.bin" into partition: <TEE1>
Loaded Firmware File: "trustzone.bin" into partition: <TEE2>
Loaded Firmware File: "secro.img" into partition: <SECRO>
Loaded Firmware File: "system.img" into partition: <SYSTEM>
Loaded Firmware File: "cache.img" into partition: <CACHE>
Scatter File's Partition <USERDATA> Cannot be Found in the Current Layout. Cannot Inject its File "userdata.img"

Operation complete. From Scatter File were Loaded 16 partitons. Skipped 2 partitions.


Now simply click "Write selected" and wait for process to finish.


Then, close plugin and switch to "eMMC/SD Access". Select boot partition 1, enter start address 0x0000 0000 0000 and open preloader file "preloader_wt6750s_66_s11_n.bin" . Click "Write memory" and when its done You should have working phone.

[otherboy123]

when i hit "Load layout from Device"
software hand and close what i need to fix?

Imgur: The magic of the Internet

[otherboy123]

here is sign firmware
Seite nicht gefunden
recovery firmware
Link

[Legija]

Hi,
I dont have pinout, but You can use that GPT partition to write it.
As eMMC is erased, process for repair needs MBR write at the end (all steps above should be done first)


Open file in eMMC plugin, tick "Show Gaps" click "Load layout from file" and select MBR partition (double click) and then simply click "Write Selected".


I hope this will help.


For ISP pinout, maybe You can track pins after You remove chip.

[otherboy123]

Hi,
I dont have pinout, but You can use that GPT partition to write it.
As eMMC is erased, process for repair needs MBR write at the end (all steps above should be done first)


Open file in eMMC plugin, tick "Show Gaps" click "Load layout from file" and select MBR partition (double click) and then simply click "Write Selected".


I hope this will help.


For ISP pinout, maybe You can track pins after You remove chip.

Very nice master now writing firmware
I am waiting

[Legija]

No, something is wrong there. I don't see that scatter file is parsed and partitions inserted.


This is how it must look after steps:
1. Open PGPT.bin
2. Click "Load layout from file"
3. Click "Load Firmware files" -> select scatter file
4. Click "Write selected"

[otherboy123]

No, something is wrong there. I don't see that scatter file is parsed and partitions inserted.


This is how it must look after steps:
1. Open PGPT.bin
2. Click "Load layout from file"
3. Click "Load Firmware files" -> select scatter file
4. Click "Write selected"

I choices wrong partition for flash ?right
Master I hope Resurrector File for this model

[otherboy123]

Now correct ?

[otherboy123]

Writing firmware

[Legija]

Ok, this is fine.
After You finish this step, click again "Load layout from file" to reset, and then simply double click "MBR" partition, click write and You can close eMMC plugin to proceed with preloader on eMMC/SD tab.