G532F/M repair EMMC problem

[CubaCenter]

Hi i've my phone conected as pinout say, i can read info from emmc card, but can't repair, check:
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.48 (RIFFBOX1), JTAG Manager Version: 1.74

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 1.80V, SD_CLK Frequency is 960 KHz

Memory Type .......................... eMMC
Manufacturer ID ...................... 0x90
OEM/Application ID ................... 0x4A
Product Name ......................... "H8G4u "
Package .............................. BGA
User Area Partition Size ............. 0x0001D2000000 Bytes (7.28 GB)
Boot Partition Size .................. 0x000000400000 Bytes (4.00 MB)
RPMB Partition Size .................. 0x000000400000 Bytes (4.00 MB)
OCR Register ......................... 0xC0FF8080 (Dual Voltage, High Capacity)
Write Protection Bits ................ NONE
ExtCSD Register Fields ............... [177] = 0x00, [179] = 0x48, [162] = 0x01
Boot Configuration ................... Boot from Boot Partition 1 (Bus Width = 1Bit)
Chip Revision ........................ 0.1
Multimedia Card Revision ............. 1.7 (eMMC v5.0)
Serial Number ........................ 0x32393408
Memory Manufacturing Date ............ July, 2017

But when want to repair with G532G DLL for emmc:
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.48 (RIFFBOX1), JTAG Manager Version: 1.74
Selected Resurrector: [Samsung G532G ISP V1.0.6482.19990]

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 1.80V, SD_CLK Frequency is 960 KHz

Detected eMMC Chip, ID: 0x90/0x4A (H8G4u ), User Area Partition = 0x0001D2000000 Bytes (7.28 GB)

Selected Resurrection Data for the eMMC Chip with Capacity = 7,28 GB

Flashing the dead body...

And just stay there, i don't know if it's because G532"G", and not "F/M".
In advance i can't read firmware:
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.48 (RIFFBOX1), JTAG Manager Version: 1.74

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 1.80V, SD_CLK Frequency is 960 KHz

Detected eMMC Chip, ID: 0x90/0x4A (H8G4u ), User Area Partition = 0x0001D2000000 Bytes (7.28 GB)

Reading the [KLM8G2YE4C-C001] eMMC Core Firmware...
ERROR: Read Failed with Error Code: (11:68). Terminating at 0x000000040000ERROR
ERROR: Reading eMMC Core Firmware Failed

But i can update
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.48 (RIFFBOX1), JTAG Manager Version: 1.74

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 1.80V, SD_CLK Frequency is 960 KHz

Detected eMMC Chip, ID: 0x90/0x4A (H8G4u ), User Area Partition = 0x0001D2000000 Bytes (7.28 GB)

How can i fix my phone? I hope I can solve it thanks!!!

[Legija]

Hi,

Let's do things step by step here.

First, open eMMC/SD tab and read boot partition 1 (tick autofullflash size).
Then, select "User Area Partition" untick "Autofullflash size" and for data length select 512MB, then click Read.
After reading is done, click "Save".
Post logs here.

[CubaCenter]

hi, thanks for fast answer, this is log:
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.48 (RIFFBOX1), JTAG Manager Version: 1.74

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 1.80V, SD_CLK Frequency is 960 KHz

Detected eMMC Chip, ID: 0x90/0x4A (H8G4u ), User Area Partition = 0x0001D2000000 Bytes (7.28 GB)

Reading "Boot Area Partition 1" address space from 0x000000000000 to 0x00001FFFFFFF
ERROR: Read Failed with Error Code: (01:71). Terminating at 0x000000000000

[Legija]

Where is log from boot partition 1 ?

[CubaCenter]

Forgot here u got

Where is log from boot partition 1 ?

[Legija]

Still need to see the log from reading boot partition 1.

[CubaCenter]

I made what u have ask to me, save and upload file, could u check it?

[Legija]

You just saved 0 bytes file . . .
I need to see LOG, like You posted for user area partition.

Obviously, something is wrong. Let's see - can You tell me status of phone it self - how it died, is it detected on USB port and so on.

Next, some info about ISP connection.

Have You powered phone it self by any means - usb cable/battery or not ?
Have You connected GND to nearest point of other connection points ?
Have You connected VCC from RIFF Box or from external adaptor ?
Same for VCCIO (VCCQ)
. . .
Have You tried setting different clock ?

[CubaCenter]

It's just i got that message, i can not read, got error.

It's died because i was trying to put an spanish firmware and flashed it wrong , when i conect usb its mediatek port

Next, some info about ISP connection.

Have You powered phone it self by any means - usb cable/battery or not ?
USB cable
Have You connected GND to nearest point of other connection points ?
GND it's conected to mainboard
Have You connected VCC from RIFF Box or from external adaptor ?
Same for VCCIO (VCCQ)
All have been conected with rj45 riff no external
. . .
Have You tried setting different clock ?
I've not.. should i?
[/QUOTE]

[Legija]

I dont think You should have connected USB cable to phone. That way CPU is powered on, and of course it takes control over data bus.

Just connect VCC and VCCQ from RIFF Box or via external adapter, that should be enough to power eMMC chip.

Then get it detected and try reading again.

NEVER try "Resurrection" first on unsupported models, before making backup !

[CubaCenter]

Worked! Adapter needed power external supply, not mainboard, it's reading! Please stay online i wil upload boot in few minutes. And good to know make backup, but... how should be done backup before resurrection on "no supported" phone? Thanks!

[Legija]

Right now You have "not supported model" and still reading backup

Now just do as said before - read boot partition 1, read 512MB from user partition, and also not bad idea to read emmc info on emmc advanced page, and save it, of course.

Good info would be if You know exact fw version which was in phone before You "espanoled" it

[CubaCenter]

Great, then from now on, boot partition 1 512mb and emmc info in advanced for backup any emmc.
fw i don't know which one but model was sm-g532g/ds manufactured in vietnam, just english and viet langugage.
Do u think i can recover phone and put it into spanish finally?
How would i should do that? You still need to check boot file? Thanks for great support!

Right now You have "not supported model" and still reading backup

Now just do as said before - read boot partition 1, read 512MB from user partition, and also not bad idea to read emmc info on emmc advanced page, and save it, of course.

Good info would be if You know exact fw version which was in phone before You "espanoled" it

[Legija]

Yes, I need both files to be uploaded here. I hope that You have decent enough internet connection.

Not sure about region conversion for that samsung model, for start we will try to power it on first.
We need to get that Vietnamese firmware to extract required files.

[CubaCenter]

I've 100mb line, so i can upload 10mb/s. Delay is on ready 100kb/s, is 68%, and timeleft is 27 min. Also, will be able to upload heavy file here or should i use mega?
I think can do it using kies, with model and S/N, or do u think any other way?