j700H boot repair

[budukbol]

please i need help, i need a guide and a file to use to revive thin j700H dead after flash, tnx


i extracted this boot from tested stock rom, but how can i use this with riff

4shared.com - free file sharing and storage

[VIPER_GE]

ask Legija

[alexjuve42]

connect direct emmc and use emmc tab on riff box

[MARVZ_TG]

need hellp team & riff box expert

hello team & riff box expert

can you help tested modification to my riff box cant detect direct emmc

my box full activated EMMC & PKG

I HAVE J700H DEAD BOOT

Signing in to the RIFFBOX Server...OK

Account Type ........................... ACTIVE
Registered Name ........................ [MARVZ_TG]
Registered e-Mail ...................... [marvz_tg29@yahoo.com]
Expiration Date ........................ [7/15/2017 8:42:07 AM]
Available Credits ...................... 0
Packages Root Permissions .............. YES

THIS MODEL NOT DEAD EMMC ALREADY DETECT ON OTHER JTAG

Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: 161609229E54864B, ,FW Ver.: 01.55
CMD Pullup Level:474 mV
CMD Active Level:2351 mV
Box IO Level:3300 mV
CLK Rate:14000 khz
HiPower™ mode is off!
eMMC Device Information
EMMC CID : 1101003430303037330084DA289962D6
EMMC CSD : D07E00320F5903FFFFFFFFE78A4000D0
EMMC Manufacturer ID: 0011 , OEM ID: 0100
EMMC Date: 06/2015 Rev.0x0
EMMC NAME: 400073 , S/N: 2228889753
EMMC NAME (HEX): 34303030373300
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.7 (MMC 5.0)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x00
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: 400073_2228889753_20160715_1950.extcsd
Done.

[Legija]

There is RJ45 port pinout in RIFF JTAG Manager Interface. (RIFF JTAG Pinout button)

For ISP connection You have to add pull up resistors from VCCQ to both SD_CMD and SD_DAT0 lines. 100 or 200 ohms value.

If You connect everything properly, it must work, otherwise Your box could be damaged.

[MARVZ_TG]

There is RJ45 port pinout in RIFF JTAG Manager Interface. (RIFF JTAG Pinout button)

For ISP connection You have to add pull up resistors from VCCQ to both SD_CMD and SD_DAT0 lines. 100 or 200 ohms value.

If You connect everything properly, it must work, otherwise Your box could be damaged.

what if my box is damage how to repair..? if cant repair my activation is useless

[Legija]

what if my box is damage how to repair..? if cant repair my activation is useless

That is remote possibility, it's more probable that You just misunderstood instructions and wrongly connected something.

[MARVZ_TG]

OK tomorrow i well try your guide

by the way sir thank you for reply my thread

sir you have dump file or PKG file for j700h

[Legija]

Yes I will prepare it.

[MARVZ_TG]

Sir Did you upload in support area..?

[MARVZ_TG]

hello sir finally i got it.

sir can you guide me how to revive my j700h

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.40 (RIFFBOX1), JTAG Manager Version: 1.62

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 3.30V, SD_CLK Frequency is 393 KHz

Memory Type .......................... eMMC
Manufacturer ID ...................... 0x11
OEM/Application ID ................... 0x00
Product Name ......................... "400073"
Package .............................. BGA
User Area Partition Size ............. 0x0003AB400000 Bytes (14.68 GB)
Boot Partition Size .................. 0x000000400000 Bytes (4.00 MB)
RPMB Partition Size .................. 0x000000400000 Bytes (4.00 MB)
OCR Register ......................... 0xC0FF8080 (Dual Voltage, High Capacity)
Write Protection Bits ................ NONE
Boot Configuration ................... Boot from Boot Partition 1 (Bus Width = 4Bit)
Chip Revision ........................ 0.0
Multimedia Card Revision ............. 1.7 (eMMC v5.0)
Serial Number ........................ 0x84DA2899
Memory Manufacturing Date ............ July, 2015

[Legija]

Ok, give me few moments to prepare PKG for You.

[MARVZ_TG]

ok sir im waiting

[Legija]

Unlock Forum - RIFF Box support forum

Before You click "resurrection" read backups:

- User Area partition - 256MB
- Boot partition 1 - full
- Boot partition 2 - full

Then report results with PKG, please.

[MARVZ_TG]

WHATS WRONG SIR..?

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.40 (RIFFBOX1), JTAG Manager Version: 1.62

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 3.30V, SD_CLK Frequency is 2.50 MHz

Detected eMMC Chip, ID: 0x11/0x00 (400073), User Area Partition = 0x0003AB400000 Bytes (14.68 GB)

Reading "User Area Partition" address space from 0x000000000000 to 0x000010000000
Failed to receive answer to READ command.