Announcement

Collapse
No announcement yet.

Beta test reports

Collapse
X
Collapse
 
  • Page of 9
  • Filter
  • Time
  • Show
Clear All
new posts
Previous 1 2 3 4 5 6 9 template Next
  • #31
    Mr. Legija
    I can't connect/check eMMC manufacturing by Toshiba with PN : 032GE4 32GB
    i try with other box is can...
    i'm use moorc adapter

    log:

    Open serial port...OK
    Connecting to the RIFF Box...OK
    Firmware Version: 1.38.5b, JTAG Manager Version: 1.57 [BETA 3]

    Connecting to the SD/eMMC Card...ERROR
    Set I/O Voltage reads as 3.30V, SD_CLK Frequency is 2.50 MHz

    Connecting to the SD/eMMC Card Failed (ERR[0075], POS[000B])


    Attached Files

    Comment

    • #32
      Check wires and pinout.

      Comment

      • #33
        Tested Samsung P3100 connect.
        Connected ISP

        Открытие порта...OK
        Подключение к RIFF Боксу...OK
        Версия Прошивки: 1.38.5b, Версия JTAG Manager: 1.57 [BETA 3]

        Connecting to the SD/eMMC Card...OK
        Выставленное I/O Напряжение 3.29V, SD_CLK Frequency is 2.50 MHz

        Memory Type .......................... eMMC
        Manufacturer ID ...................... 0x15
        OEM/Application ID ................... 0x00
        Product Name ......................... "M8G2FB"
        Package .............................. BGA
        User Area Partition Size ............. 0x0001D2000000 Bytes (7.28 GB)
        Boot Partition Size .................. 0x000000200000 Bytes (2.00 MB)
        RPMB Partition Size .................. 0x000000020000 Bytes (128.00 KB)
        OCR Register ......................... 0xC0FF8080 (Dual Voltage, High Capacity)
        Write Protection Bits ................ NONE
        Boot Configuration ................... No Boot
        Chip Revision ........................ 0.8
        Multimedia Card Revision ............. 1.5 (eMMC v4.41)
        Serial Number ........................ 0x84E9514A
        Memory Manufacturing Date ............ August, 2012
        Открытие порта...OK
        Подключение к RIFF Боксу...OK
        Версия Прошивки: 1.38.5b, Версия JTAG Manager: 1.57 [BETA 3]

        Connecting to the SD/eMMC Card...OK
        Выставленное I/O Напряжение 3.29V, SD_CLK Frequency is 2.50 MHz

        Detected eMMC Chip, ID: 0x15/0x00 (M8G2FB), User Area Partition = 0x0001D2000000 Bytes (7.28 GB)

        Reading SMART Info from Samsung eMMC Chip...OK

        Super Block Size ..................... 0x00400000 Bytes
        Super Page Size ...................... 0x00004000 Bytes
        Optimal Write Size ................... 0x00008000 Bytes
        Number of Banks ...................... 2
        Bank0 Init Bad Block ................. 0
        Bank0 Runtime Bad Block .............. 7
        Bank0 Remain Reserved Block .......... 22
        Bank1 Init Bad Block ................. 0
        Bank1 Runtime Bad Block .............. 5
        Bank1 Remain Reserved Block .......... 24
        Max Erase Count ...................... 1286
        Min Erase Count ...................... 0
        Avg Erase Count ...................... 1184
        Read Reclaim Count ................... 0
        Optimal Trim Size .................... 0x00008000 Bytes
        Hash Code ............................ F79F50C3E9F83231FDE4D1D0ED2B76BAF12C7E8C6F26501983 DD663F1FA22B5D
        Max Erase Count (SLC) ................ 1200
        Min Erase Count (SLC) ................ 0
        Avg Erase Count (SLC) ................ 894
        Max Erase Count (MLC) ................ 1286
        Min Erase Count (MLC) ................ 1150
        Avg Erase Count (MLC) ................ 1187
        Attached Files

        Comment

        • #34
          Samsung P5110 ISP

          Open serial port...OK
          Connecting to the RIFF Box...OK
          Firmware Version: 1.38.5b, JTAG Manager Version: 1.57 [BETA 3]

          Connecting to the SD/eMMC Card...OK
          Set I/O Voltage reads as 1.80V, SD_CLK Frequency is 649 KHz

          Memory Type .......................... eMMC
          Manufacturer ID ...................... 0x15
          OEM/Application ID ................... 0x00
          Product Name ......................... "MAG2GA"
          Package .............................. BGA
          User Area Partition Size ............. 0x0003AB400000 Bytes (14.68 GB)
          Boot Partition Size .................. 0x000000200000 Bytes (2.00 MB)
          RPMB Partition Size .................. 0x000000020000 Bytes (128.00 KB)
          OCR Register ......................... 0xC0FF8080 (Dual Voltage, High Capacity)
          Write Protection Bits ................ NONE
          Boot Configuration ................... No Boot
          Chip Revision ........................ 0.7
          Multimedia Card Revision ............. 1.5 (eMMC v4.41)
          Serial Number ........................ 0xFF7264F3
          Memory Manufacturing Date ............ December, 2012


          Read

          Open serial port...OK
          Connecting to the RIFF Box...OK
          Firmware Version: 1.38.5b, JTAG Manager Version: 1.57 [BETA 3]

          Connecting to the SD/eMMC Card...OK
          Set I/O Voltage reads as 2.70V, SD_CLK Frequency is 649 KHz

          Detected eMMC Chip, ID: 0x15/0x00 (MAG2GA), User Area Partition = 0x0003AB400000 Bytes (14.68 GB)

          Reading "User Area Partition" address space from 0x000000000000 to 0x0000001FFFFF
          Failed to receive answer to READ command.

          Comment

          • #35
            Originally posted by Serg55 View Post
            Samsung P5110 ISP



            Read
            try it under 2.5mhz

            Comment

            • #36
              Transcend SD HC

              Open serial port...OK
              Connecting to the RIFF Box...OK
              Firmware Version: 1.38.5b, JTAG Manager Version: 1.57 [BETA 3]

              Connecting to the SD/eMMC Card...OK
              Set I/O Voltage reads as 3.28V, SD_CLK Frequency is 490 KHz

              Memory Type .......................... SDHC
              Manufacturer ID ...................... 0x04
              OEM/Application ID ................... " A"
              Product Name ......................... "SMI-S"
              Package .............................. Removable
              User Area Partition Size ............. 0x0001B6E00000 Bytes (6.86 GB)
              OCR Register ......................... 0x80FF8000 (High Voltage, High Capacity)
              Write Protection Bits ................ NONE
              Chip Revision ........................ 4.4
              Serial Number ........................ 0x03000000
              Memory Manufacturing Date ............ July, 2001

              Comment

              • #37
                Open serial port...OK
                Connecting to the RIFF Box...OK
                Firmware Version: 1.38.5b, JTAG Manager Version: 1.57 [BETA 3]

                Connecting to the SD/eMMC Card...
                ERROR: Set I/O Voltage to 0.00V failed. Real reading is 1.34V

                Comment

                • #38
                  @shoaibrao Set i/o voltage to 3.3v

                  Comment

                  • #39
                    Originally posted by aleksa94 View Post
                    @shoaibrao Set i/o voltage to 3.3v
                    I Am Using Moorc Adapter
                    RIFF Log
                    Code:
                    Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.38.5b, JTAG Manager Version: 1.57 [BETA 3]

Connecting to the SD/eMMC Card...ERROR
Set I/O Voltage reads as 3.29V, SD_CLK Frequency is 649 KHz

Connecting to the SD/eMMC Card Failed (ERR[0071], POS[0001])
                    EasyJTAG Tool Log

                    Code:
                    Loading eMMC Addon Firmware... IO: 1800 mV

CMD Pullup Level:1165 mV
CMD Active Level:1598 mV
HiPower™ mode is off!
eMMC Device Information
EMMC CID : 7001004D4D4330344758A9C8D5047160
EMMC CSD : D04F01320F5903FFFFFFFFE78A400050
EMMC Manufacturer ID: 0070 , OEM ID: 0100
EMMC Date: 07/2014 Rev.0x58
EMMC NAME: MMC04G , S/N: 2848511236
EMMC NAME (HEX): 4D4D4330344700 
EMMC ROM1 (Main User Data) Capacity: 3688 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x01
Backup saved: MMC04G_2848511236_20160229_1450.extcsd
Done.

                    Comment

                    • #40
                      Riff box 8.1 is compatible with Windows 32 and 64 bit

                      Greetings friends I would like to know if you can use the software in Windows 8.1 Riff 32 and 64 bits

                      Comment

                      • #41
                        Beta 4

                        Oppo R1001 Connected By ISP
                        Code:
                        Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.38.6b, JTAG Manager Version: 1.57 [BETA 4]

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 2.80V, SD_CLK Frequency is 649 KHz

Memory Type .......................... eMMC
Manufacturer ID ...................... 0x90
OEM/Application ID ................... 0x4A
Product Name ......................... "H4G1d "
Package .............................. BGA
User Area Partition Size ............. 0x0000E9000000 Bytes (3.64 GB)
Boot Partition Size .................. 0x000000400000 Bytes (4.00 MB)
RPMB Partition Size .................. 0x000000400000 Bytes (4.00 MB)
OCR Register ......................... 0xC0FF8080 (Dual Voltage, High Capacity)
Write Protection Bits ................ NONE
Boot Configuration ................... Boot from Boot Partition 1 (Bus Width = 1Bit)
Chip Revision ........................ 0.5
Multimedia Card Revision ............. 1.6 (eMMC v4.5, v4.51)
Serial Number ........................ 0x00A19032
Memory Manufacturing Date ............ June, 2014

                        User Area Forced Erase
                        Code:
                        Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.38.6b, JTAG Manager Version: 1.57 [BETA 4]

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 2.80V, SD_CLK Frequency is 649 KHz

Detected eMMC Chip, ID: 0x90/0x4A (H4G1d ), User Area Partition = 0x0000E9000000 Bytes (3.64 GB)

Erasing User Area and resetting Password...OK (Completed in 00:03.369)

                        Comment

                        • #42
                          Open serial port...OK
                          Connecting to the RIFF Box...OK
                          Firmware Version: 1.38.6b, JTAG Manager Version: 1.57 [BETA 4]
                          Selected Resurrector: [Samsung I545 V1.0.5067.52868]

                          Connecting to the dead body...OK
                          Detected dead body ID: 0x2071B0E1 - CORRECT!
                          Set I/O Voltage reads as 1.79V, TCK Frequency is RTCK
                          Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz]

                          Resurrection sequence started.
                          Establish communication with the phone...OK
                          Initializing internal hardware configuration...OK
                          Uploading resurrector data into memory...OK
                          Starting communication with resurrector...FAILED
                          ERROR: No response from the RIFF Box.

                          what is the problem?

                          Comment

                          • #43
                            Originally posted by raxim View Post
                            Open serial port...OK
                            Connecting to the RIFF Box...OK
                            Firmware Version: 1.38.6b, JTAG Manager Version: 1.57 [BETA 4]
                            Selected Resurrector: [Samsung I545 V1.0.5067.52868]

                            Connecting to the dead body...OK
                            Detected dead body ID: 0x2071B0E1 - CORRECT!
                            Set I/O Voltage reads as 1.79V, TCK Frequency is RTCK
                            Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz]

                            Resurrection sequence started.
                            Establish communication with the phone...OK
                            Initializing internal hardware configuration...OK
                            Uploading resurrector data into memory...OK
                            Starting communication with resurrector...FAILED
                            ERROR: No response from the RIFF Box.

                            what is the problem?
                            for resurection use only 1.56 version, beta version work only eMMC function.

                            Comment

                            • #44
                              Nokia Lumia 625

                              Nokia Lumia 625
                              Connected By ISP

                              info
                              HTML Code:
                              Открытие порта...OK
Подключение к RIFF Боксу...OK
Версия Прошивки: 1.38.6b, Версия JTAG Manager: 1.57 [BETA 4]

Connecting to the SD/eMMC Card...OK
Выставленное I/O Напряжение 3.28V, SD_CLK Frequency is 2.50 MHz

Memory Type .......................... eMMC
Manufacturer ID ...................... 0x90
OEM/Application ID ................... 0x4A
Product Name ......................... "H8G2d "
Package .............................. BGA
User Area Partition Size ............. 0x0001CE800000 Bytes (7.23 GB)
Boot Partition Size .................. 0x000000200000 Bytes (2.00 MB)
RPMB Partition Size .................. 0x000000200000 Bytes (2.00 MB)
OCR Register ......................... 0xC0FF8080 (Dual Voltage, High Capacity)
Write Protection Bits ................ NONE
Boot Configuration ................... Boot from User Area (Bus Width = 1Bit)
Chip Revision ........................ 0.1
Multimedia Card Revision ............. 1.5 (eMMC v4.41)
Serial Number ........................ 0x00DAC2C3
Memory Manufacturing Date ............ February, 2014
                              read
                              HTML Code:
                              Открытие порта...OK
Подключение к RIFF Боксу...OK
Версия Прошивки: 1.38.6b, Версия JTAG Manager: 1.57 [BETA 4]

Connecting to the SD/eMMC Card...OK
Выставленное I/O Напряжение 3.28V, SD_CLK Frequency is 2.50 MHz

Detected eMMC Chip, ID: 0x90/0x4A (H8G2d ), User Area Partition = 0x0001CE800000 Bytes (7.23 GB)

Reading "Boot Area Partition 1" с 0x000000000000 по 0x0001FFFFFFFF
Завершено за 03:11:26.930 (Средняя Скорость: 730.27 кБ/сек)
                              Last edited by GAM; 03-01-2016, 09:50 PM.

                              Comment

                              • #45
                                LG D380
                                Direct on Board
                                info
                                Open serial port...OK
                                Connecting to the RIFF Box...OK
                                Firmware Version: 1.38.6b, JTAG Manager Version: 1.57 [BETA 4]

                                Connecting to the SD/eMMC Card...OK
                                Set I/O Voltage reads as 2.79V, SD_CLK Frequency is 421 KHz

                                Memory Type .......................... eMMC
                                Manufacturer ID ...................... 0x90
                                OEM/Application ID ................... 0x4A
                                Product Name ......................... "H4G1d "
                                Package .............................. BGA
                                User Area Partition Size ............. 0x0000E9000000 Bytes (3.64 GB)
                                Boot Partition Size .................. 0x000000400000 Bytes (4.00 MB)
                                RPMB Partition Size .................. 0x000000400000 Bytes (4.00 MB)
                                OCR Register ......................... 0xC0FF8080 (Dual Voltage, High Capacity)
                                Write Protection Bits ................ NONE
                                Boot Configuration ................... No Boot
                                Chip Revision ........................ 0.5
                                Multimedia Card Revision ............. 1.6 (eMMC v4.5, v4.51)
                                Serial Number ........................ 0x01A1DA1E
                                Memory Manufacturing Date ............ May, 2014
                                read
                                Open serial port...OK
                                Connecting to the RIFF Box...OK
                                Firmware Version: 1.38.6b, JTAG Manager Version: 1.57 [BETA 4]

                                Connecting to the SD/eMMC Card...OK
                                Set I/O Voltage reads as 2.79V, SD_CLK Frequency is 421 KHz

                                Detected eMMC Chip, ID: 0x90/0x4A (H4G1d ), User Area Partition = 0x0000E9000000 Bytes (3.64 GB)

                                Reading "Boot Area Partition 1" address space from 0x000000000000 to 0x0000003FFFFF
                                Completed in 00:01:28.421 (Average Transfer Rate: 46.32 kB/s)

                                Comment

                                Previous 1 2 3 4 5 6 9 template Next
                                Working...
                                X

                                We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.

                                By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.

                                I Agree