I9100 FLASH1 chip. Error code: 0x00000048. Help

[praji]

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.35, JTAG Manager Version: 1.49
Selected Resurrector: [Samsung I9100 V1.0.4724.60074]

Connecting to the dead body...OK
Detected dead body ID: 0x4BA00477 - CORRECT!
Set I/O Voltage reads as 2.79V, TCK Frequency is 8 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

WARNING: DCC Loader was unable to initialize FLASH1 chip. Error code: 0x00000048

No Resurrection Data is available for the eMMC Chip with Capacity = 0B
WARNING!!! Using Resurrection Data for the eMMC Chip with Capacity = 14.68GB

ERROR: Selected FLASH Chip was not initialized by the DCC Loader.

What This Problem Emmc or ??????????
Please Help

[muadaada]

please hang logo samsung i9100 stubborn buildup has been upgraded with odin but still hang logo samsung aja aja? can enter download mode but can not enter the recovery menu? box that I had the riff box, thanks in advance

[fon-tecno]

I9100 FLASH1 chip. Error code: 0x00000048. Help

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.56
Selected Resurrector: [Samsung I9100 V1.0.4850.415]

Connecting to the dead body...OK
Detected dead body ID: 0x4BA00477 - CORRECT!
Set I/O Voltage reads as 2.81V, TCK Frequency is 8 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

WARNING: DCC Loader was unable to initialize FLASH1 chip. Error code: 0x00000048

No Resurrection Data is available for the eMMC Chip with Capacity = 0B
WARNING!!! Using Resurrection Data for the eMMC Chip with Capacity = 14,68GB

ERROR: Selected FLASH Chip was not initialized by the DCC Loader.

[chandan224]

Samsung I-9100 Boot repair then error

I am sonu From Dwarka Mobile Care


My Samsung S-2 I9100 Booting problem
can I repair boot with riff box then error

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.49
Selected Resurrector: [Samsung I9100 V1.0.4850.415]
Restarting target (nRST Low then High)...OK

Connecting to the dead body...OK
Detected dead body ID: 0x4BA00477 - IGNORED!
Set I/O Voltage reads as 2.81V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

WARNING: DCC Loader was unable to initialize FLASH1 chip. Error code: 0x00000048

No Resurrection Data is available for the eMMC Chip with Capacity = 0B
WARNING!!! Using Resurrection Data for the eMMC Chip with Capacity = 14.68GB

ERROR: Selected FLASH Chip was not initialized by the DCC Loader.
Any soluition ?

[benbyben]

2 x emmc dead, only solution > replace it

[chandan224]

riff box

my riff box id pass lost
how to reset my id pass riff box ???????????

[vivek_keviv123]

try Emmc plugin. It better to use emmc plugin for flashing this type phone.

[r10gebleg]

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.56
Selected Resurrector: [Samsung I9100 V1.0.4850.415]
Restarting target (nRST Low then High)...OK

Connecting to the dead body...OK
Detected dead body ID: 0x4BA00477 - IGNORED!
WARNING: Embedded I/O Voltage is overriden to 2.60V
Set I/O Voltage reads as 2.59V, TCK Frequency is 12 MHz
WARNING: Reset Override to: [No RESET]

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

WARNING: DCC Loader was unable to initialize FLASH1 chip. Error code: 0x00000048

No Resurrection Data is available for the eMMC Chip with Capacity = 0B
WARNING!!! Using Resurrection Data for the eMMC Chip with Capacity = 14.68GB

ERROR: Selected FLASH Chip was not initialized by the DCC Loader.

[Haker5]

i have the same problem any solution after sw upgrade is dead

[dave_21]

s2

emmc 0gb it's clear :-( change emmc it's faulty (or you can changhe flat on connectore usb ...but i think emmc faulty)

[Fayej Gsm]

i9100 dead boot repair problem

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.47 (RIFFBOX2), JTAG Manager Version: 1.73
Selected Resurrector: [Samsung I9100 V1.0.4850.415]

Connecting to the dead body...OK
Detected dead body ID: 0x4BA00477 - CORRECT!
Set I/O Voltage reads as 2.80V, TCK Frequency is 8 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

WARNING: DCC Loader was unable to initialize FLASH1 chip. Error code: 0x00000048

No Resurrection Data is available for the eMMC Chip with Capacity = 0B
WARNING!!! Using Resurrection Data for the eMMC Chip with Capacity = 14.68GB

ERROR: Selected FLASH Chip was not initialized by the DCC Loader.

[spike_belmont]

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.47 (RIFFBOX2), JTAG Manager Version: 1.73
Selected Resurrector: [Samsung I9100 V1.0.4850.415]

Connecting to the dead body...OK
Detected dead body ID: 0x4BA00477 - CORRECT!
Set I/O Voltage reads as 2.80V, TCK Frequency is 8 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

WARNING: DCC Loader was unable to initialize FLASH1 chip. Error code: 0x00000048

No Resurrection Data is available for the eMMC Chip with Capacity = 0B
WARNING!!! Using Resurrection Data for the eMMC Chip with Capacity = 14.68GB

ERROR: Selected FLASH Chip was not initialized by the DCC Loader.

Error code 0x48
Returned by box’s firmware when attempt to start target running (to exit from debug/halted state) failed. Could happen when user clicks Run Target button and supplies non-existent address in current taget’s context or due to not-recoverable state of target at that moment.

[Legija]

You need to replace eMMC chip, or, if You are lucky, You can repair the chip by flashing eMMC controller firmware. For that, You need to desolder it and connect directly to RIFF box.

[GsmShafait]

i9100 boot repair problem .

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.47 (RIFFBOX1), JTAG Manager Version: 1.73
Selected Resurrector: [Samsung I9100 V1.0.4850.415]

Connecting to the dead body...OK
Detected dead body ID: 0x4BA00477 - CORRECT!
Set I/O Voltage reads as 2.79V, TCK Frequency is 8 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

WARNING: DCC Loader was unable to initialize FLASH1 chip. Error code: 0x00000048

No Resurrection Data is available for the eMMC Chip with Capacity = 0B
WARNING!!! Using Resurrection Data for the eMMC Chip with Capacity = 14.68GB

ERROR: Selected FLASH Chip was not initialized by the DCC Loader.

[GsmShafait]

I need dump file