htc mozart dead after full erase

[osip]

now phone not power on
when I try to make Resurrection

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

ERROR: No Resurrection Data is available for the NAND Chip with Page size = 2KB

before full erase Resurrection write normal, riff box saw phone

[Legija]

Hi,Can You post full log from resurrection attempt ?

[osip]

[27.03.2013 11:22:04] [START OPERATION_ID = RESURRECT]
[27.03.2013 11:22:08] Open serial port...OK
[27.03.2013 11:22:08] Connecting to the RIFF Box...OK
[27.03.2013 11:22:08] Firmware Version: 1.34, JTAG Manager Version: 1.48
[27.03.2013 11:22:08] Selected Resurrector: [HTC Mozart V1.00]
[27.03.2013 11:22:08] 
[27.03.2013 11:22:08] Connecting to the dead body...FAILED
[27.03.2013 11:22:08] None is detected.
[27.03.2013 11:22:08] [FINISH OPERATION_ID = RESURRECT]

[27.03.2013 11:26:45] [START OPERATION_ID = RESURRECT]
[27.03.2013 11:27:53] Open serial port...OK
[27.03.2013 11:27:53] Connecting to the RIFF Box...OK
[27.03.2013 11:27:53] Firmware Version: 1.34, JTAG Manager Version: 1.48
[27.03.2013 11:27:53] Selected Resurrector: [HTC Mozart V1.00]
[27.03.2013 11:27:53] 
[27.03.2013 11:27:53] Connecting to the dead body...OK
[27.03.2013 11:27:53] Detected dead body ID: 0x202400E1 - CORRECT!
[27.03.2013 11:27:53] Set I/O Voltage reads as 3.01V, TCK Frequency is 8 MHz
[27.03.2013 11:27:53] 
[27.03.2013 11:27:53] Resurrection sequence started.
[27.03.2013 11:27:53] Establish communication with the phone...OK
[27.03.2013 11:27:53] Initializing internal hardware configuration...OK
[27.03.2013 11:27:53] Uploading resurrector data into memory...OK
[27.03.2013 11:27:53] Starting communication with resurrector...OK
[27.03.2013 11:27:53] 
[27.03.2013 11:27:53] Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x66BC (512MB)
[27.03.2013 11:27:53] Selected Resurrection Data for the NAND Chip with Page size = 4KB
[27.03.2013 11:27:53] 
[27.03.2013 11:27:53] Flashing the dead body...OK
[27.03.2013 11:27:53] Resurrection complete!
[27.03.2013 11:27:53] [FINISH OPERATION_ID = RESURRECT]

[27.03.2013 11:28:23] [START OPERATION_ID = RESURRECT]
[27.03.2013 11:29:53] Open serial port...OK
[27.03.2013 11:29:53] Connecting to the RIFF Box...OK
[27.03.2013 11:29:53] Firmware Version: 1.34, JTAG Manager Version: 1.48
[27.03.2013 11:29:53] Selected Resurrector: [HTC Mozart V1.00]
[27.03.2013 11:29:53] 
[27.03.2013 11:29:53] Connecting to the dead body...OK
[27.03.2013 11:29:53] Detected dead body ID: 0x202400E1 - CORRECT!
[27.03.2013 11:29:53] Set I/O Voltage reads as 3.01V, TCK Frequency is 8 MHz
[27.03.2013 11:29:53] 
[27.03.2013 11:29:53] Resurrection sequence started.
[27.03.2013 11:29:53] Establish communication with the phone...OK
[27.03.2013 11:29:53] Initializing internal hardware configuration...OK
[27.03.2013 11:29:53] Uploading resurrector data into memory...OK
[27.03.2013 11:29:53] Starting communication with resurrector...OK
[27.03.2013 11:29:53] 
[27.03.2013 11:29:53] Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x66BC (512MB)
[27.03.2013 11:29:53] Selected Resurrection Data for the NAND Chip with Page size = 4KB
[27.03.2013 11:29:53] 
[27.03.2013 11:29:53] Flashing the dead body...OK
[27.03.2013 11:29:53] Resurrection complete!
[27.03.2013 11:29:53] [FINISH OPERATION_ID = RESURRECT]

[27.03.2013 11:33:54] [START OPERATION_ID = RESURRECT]
[27.03.2013 11:33:57] Open serial port...OK
[27.03.2013 11:33:57] Connecting to the RIFF Box...OK
[27.03.2013 11:33:57] Firmware Version: 1.34, JTAG Manager Version: 1.48
[27.03.2013 11:33:57] Selected Resurrector: [HTC Mozart V1.00]
[27.03.2013 11:33:57] 
[27.03.2013 11:33:57] Connecting to the dead body...FAILED
[27.03.2013 11:33:57] None is detected.
[27.03.2013 11:33:57] [FINISH OPERATION_ID = RESURRECT]

[27.03.2013 12:06:28] ------------------------------- JTAG Manager Session Closed -------------------------------



[27.03.2013 12:23:12] ------------------------------- JTAG Manager Session Opened -------------------------------
[27.03.2013 12:23:12] JTAG Manger Version: 1.48
[27.03.2013 12:23:12] -------------------------------------------------------------------------------------------

 
[27.03.2013 12:26:40] [START OPERATION_ID = RESURRECT]
[27.03.2013 12:26:53] Open serial port...OK
[27.03.2013 12:26:53] Connecting to the RIFF Box...OK
[27.03.2013 12:26:53] Firmware Version: 1.34, JTAG Manager Version: 1.48
[27.03.2013 12:26:53] Selected Resurrector: [HTC Mozart V1.00]
[27.03.2013 12:26:53] 
[27.03.2013 12:26:53] Connecting to the dead body...OK
[27.03.2013 12:26:53] Detected dead body ID: 0x202400E1 - CORRECT!
[27.03.2013 12:26:53] Set I/O Voltage reads as 2.99V, TCK Frequency is 8 MHz
[27.03.2013 12:26:53] 
[27.03.2013 12:26:53] Resurrection sequence started.
[27.03.2013 12:26:53] Establish communication with the phone...OK
[27.03.2013 12:26:53] Initializing internal hardware configuration...OK
[27.03.2013 12:26:53] Uploading resurrector data into memory...OK
[27.03.2013 12:26:53] Starting communication with resurrector...OK
[27.03.2013 12:26:53] 
[27.03.2013 12:26:53] Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x66BC (512MB)
[27.03.2013 12:26:53] [FINISH OPERATION_ID = RESURRECT]

[27.03.2013 12:27:02] [START OPERATION_ID = DCC_ERASE_MEMORY]
[27.03.2013 12:27:16] Open serial port...OK
[27.03.2013 12:27:16] Connecting to the RIFF Box...OK
[27.03.2013 12:27:16] Firmware Version: 1.34, JTAG Manager Version: 1.48
[27.03.2013 12:27:16] Selected Resurrector: [HTC Mozart V1.00]
[27.03.2013 12:27:16] 
[27.03.2013 12:27:16] Connecting to the dead body...OK
[27.03.2013 12:27:16] Detected dead body ID: 0x202400E1 - CORRECT!
[27.03.2013 12:27:16] Set I/O Voltage reads as 2.99V, TCK Frequency is 8 MHz
[27.03.2013 12:27:16] Settings Code: 0x05010B00000000400000000001400000
[27.03.2013 12:27:16] 
[27.03.2013 12:27:16] Resurrection sequence started.
[27.03.2013 12:27:16] Establish communication with the phone...OK
[27.03.2013 12:27:16] Initializing internal hardware configuration...OK
[27.03.2013 12:27:16] Uploading resurrector data into memory...OK
[27.03.2013 12:27:16] Starting communication with resurrector...OK
[27.03.2013 12:27:16] 
[27.03.2013 12:27:16] Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x66BC (512MB)
[27.03.2013 12:27:16] 
[27.03.2013 12:27:16] Erasing FLASH1 memory from 0x000000000000 to 0x00001FFFFFFF...OK
[27.03.2013 12:27:16] WARNING: Erasing Error (0x24) at 0x000017A40000. Attempt to Repeat again.
[27.03.2013 12:27:16] WARNING: Erasing Error (0x24) at 0x000017A40000. Attempt to Repeat again.
[27.03.2013 12:27:16] WARNING: Erasing Error (0x24) at 0x000017A40000. Attempt to Repeat again.
[27.03.2013 12:27:16] WARNING: Erasing Error (0x24) at 0x000017A40000. Attempt to Repeat again.
[27.03.2013 12:27:16] WARNING: Erasing Error (0x24) at 0x000017A40000. Attempt to Repeat again.
[27.03.2013 12:27:16] WARNING: Erasing Error (0x24) at 0x000017A40000. Attempt to Repeat again.
[27.03.2013 12:27:16] WARNING: Erasing Error (0x24) at 0x000017A40000 is Ignored. Erase continues.
[27.03.2013 12:27:16] Completed in 00:00:11.438 (Average Transfer Rate: 45837.38 kB/s)
[27.03.2013 12:27:16] [FINISH OPERATION_ID = DCC_ERASE_MEMORY]

[27.03.2013 12:27:22] [START OPERATION_ID = RESURRECT]
[27.03.2013 12:27:27] Open serial port...OK
[27.03.2013 12:27:27] Connecting to the RIFF Box...OK
[27.03.2013 12:27:27] Firmware Version: 1.34, JTAG Manager Version: 1.48
[27.03.2013 12:27:27] Selected Resurrector: [HTC Mozart V1.00]
[27.03.2013 12:27:27] 
[27.03.2013 12:27:27] Connecting to the dead body...OK
[27.03.2013 12:27:27] Detected dead body ID: 0x202400E1 - CORRECT!
[27.03.2013 12:27:27] Set I/O Voltage reads as 2.99V, TCK Frequency is 8 MHz
[27.03.2013 12:27:27] 
[27.03.2013 12:27:27] Resurrection sequence started.
[27.03.2013 12:27:27] Establish communication with the phone...OK
[27.03.2013 12:27:27] Initializing internal hardware configuration...OK
[27.03.2013 12:27:27] Uploading resurrector data into memory...OK
[27.03.2013 12:27:27] Starting communication with resurrector...OK
[27.03.2013 12:27:27] 
[27.03.2013 12:27:27] [FINISH OPERATION_ID = RESURRECT]

[27.03.2013 12:27:30] [START OPERATION_ID = RESURRECT]
[27.03.2013 12:27:50] Open serial port...OK
[27.03.2013 12:27:50] Connecting to the RIFF Box...OK
[27.03.2013 12:27:50] Firmware Version: 1.34, JTAG Manager Version: 1.48
[27.03.2013 12:27:50] Selected Resurrector: [HTC Mozart V1.00]
[27.03.2013 12:27:50] 
[27.03.2013 12:27:50] Connecting to the dead body...OK
[27.03.2013 12:27:50] Detected dead body ID: 0x202400E1 - CORRECT!
[27.03.2013 12:27:50] Set I/O Voltage reads as 2.99V, TCK Frequency is 8 MHz
[27.03.2013 12:27:50] 
[27.03.2013 12:27:50] Resurrection sequence started.
[27.03.2013 12:27:50] Establish communication with the phone...OK
[27.03.2013 12:27:50] Initializing internal hardware configuration...OK
[27.03.2013 12:27:50] Uploading resurrector data into memory...OK
[27.03.2013 12:27:50] Starting communication with resurrector...OK
[27.03.2013 12:27:50] 
[27.03.2013 12:27:50] ERROR: No Resurrection Data is available for the NAND Chip with Page size = 2KB
[27.03.2013 12:27:50] [FINISH OPERATION_ID = RESURRECT]

[27.03.2013 12:28:09] [START OPERATION_ID = RESURRECT]
[27.03.2013 12:28:14] Open serial port...OK
[27.03.2013 12:28:14] Connecting to the RIFF Box...OK
[27.03.2013 12:28:14] Firmware Version: 1.34, JTAG Manager Version: 1.48
[27.03.2013 12:28:14] Selected Resurrector: [HTC Mozart V1.00]
[27.03.2013 12:28:14] 
[27.03.2013 12:28:14] Connecting to the dead body...OK
[27.03.2013 12:28:14] Detected dead body ID: 0x202400E1 - CORRECT!
[27.03.2013 12:28:14] Set I/O Voltage reads as 2.99V, TCK Frequency is 8 MHz
[27.03.2013 12:28:14] 
[27.03.2013 12:28:14] Resurrection sequence started.
[27.03.2013 12:28:14] Establish communication with the phone...OK
[27.03.2013 12:28:14] Initializing internal hardware configuration...OK
[27.03.2013 12:28:14] Uploading resurrector data into memory...OK
[27.03.2013 12:28:14] Starting communication with resurrector...OK
[27.03.2013 12:28:14] 
[27.03.2013 12:28:14] ERROR: No Resurrection Data is available for the NAND Chip with Page size = 2KB
[27.03.2013 12:28:14] [FINISH OPERATION_ID = RESURRECT]

[27.03.2013 12:28:44] [START OPERATION_ID = RESURRECT]
[27.03.2013 12:28:50] Open serial port...OK
[27.03.2013 12:28:50] Connecting to the RIFF Box...OK
[27.03.2013 12:28:50] Firmware Version: 1.34, JTAG Manager Version: 1.48
[27.03.2013 12:28:50] Selected Resurrector: [HTC Mozart V1.00]
[27.03.2013 12:28:50] 
[27.03.2013 12:28:50] Connecting to the dead body...OK
[27.03.2013 12:28:50] Detected dead body ID: 0x202400E1 - CORRECT!
[27.03.2013 12:28:50] Set I/O Voltage reads as 2.99V, TCK Frequency is 8 MHz
[27.03.2013 12:28:50] 
[27.03.2013 12:28:50] Resurrection sequence started.
[27.03.2013 12:28:50] Establish communication with the phone...OK
[27.03.2013 12:28:50] Initializing internal hardware configuration...OK
[27.03.2013 12:28:50] Uploading resurrector data into memory...OK
[27.03.2013 12:28:50] Starting communication with resurrector...OK
[27.03.2013 12:28:50] 
[27.03.2013 12:28:50] ERROR: No Resurrection Data is available for the NAND Chip with Page size = 2KB
[27.03.2013 12:28:50] [FINISH OPERATION_ID = RESURRECT]

[Legija]

Hi,It appears that there is some hardware problem with Your phone board.NAND chip is not detected properly, and You should try to reball it and resolder.

[osip]

phone regularly worked, I wanted to lower SPL. At first I made Resurrection, everything turned out, but SPL didn't go down. Then I started ALL ERASE and phone didn't begin to read Resurrection

[Legija]

Yes, I understood that. But as You can see in log, NAND chip is not detected at all now.