Unable to unlock W490, Here is the log
Selected: Motorola W490, firmware: R452G
Clicked button: UNLOCK (&Unlock)
On WIZARD selected: &This is a new phone. Need to do default prepare stage
On WIZARD selected: &No luck with default prepare stage. Need to try an alternative prepare.
On WIZARD clicked: CONTINUE button
On WIZARD accepted port: COM138
Detected motorola interface: Motorola Flash
Full bootcore version: 011302FF00000C50
Full firmware version: R452G_G_08.24.02R:GSVPEMBATMB02NA0DC
Decision: bootcore flashing needed.
The ExTespoint's COM port is connected.
Full bootcore version: 011302FF00000C50
Full firmware version: R452G_G_08.24.02R:GSVPEMBATMB02NA0DC
Uploading ramloader of version: 0C.50
Reading 131072 bytes...
Reading 65536 bytes...
Reading 131072 bytes...
Show WINDOW: Head = "Stage complete.", line1 = "Please wait till phone is powered on or put it to flash mode manually.", line2 = "Wait for phone to be detected (see below). Then Click Continue...", line3 = "", button1 = "", button2 = "&Continue"
Showed WINDOW modal result: 2
Full bootcore version: 011302FF00000C50
Full firmware version: R452G_G_08.24.02R:GSVPEMBATMB02NA0DC
Uploading ramloader of version: 0C.50
Show WINDOW: Head = "Stage complete.", line1 = "Please wait till phone is powered on or put it to flash mode manually.", line2 = "Wait for phone to be detected (see below). Then Click Continue...", line3 = "", button1 = "", button2 = "&Continue"
Showed WINDOW modal result: 2
Show WINDOW: Head = "Stage complete.", line1 = "Your phone now is ready for the ExTestpoint stage.", line2 = "1. Make sure the USB (EMU) cable is plugged into phone and connected to the PC.", line3 = "2. Make sure the LCD is disconnected from the board.", button1 = "", button2 = "&OK"
Showed WINDOW modal result: 2
The ExTespoint's COM port is connected.
ExTP window: clicked the START (&Start) button.
ExTP window: Started enumeration sequence.
ExTP window: Power switched ON. Wait for device to enumerate...
ExTP window: Sorry, no success. Not expected bootcore version: 0C50
Selected: Motorola W490, firmware: R452G
Clicked button: UNLOCK (&Unlock)
On WIZARD selected: &This is a new phone. Need to do default prepare stage
On WIZARD selected: &No luck with default prepare stage. Need to try an alternative prepare.
On WIZARD clicked: CONTINUE button
On WIZARD accepted port: COM138
Detected motorola interface: Motorola Flash
Full bootcore version: 011302FF00000C50
Full firmware version: R452G_G_08.24.02R:GSVPEMBATMB02NA0DC
Decision: bootcore flashing needed.
The ExTespoint's COM port is connected.
Full bootcore version: 011302FF00000C50
Full firmware version: R452G_G_08.24.02R:GSVPEMBATMB02NA0DC
Uploading ramloader of version: 0C.50
Reading 131072 bytes...
Reading 65536 bytes...
Reading 131072 bytes...
Show WINDOW: Head = "Stage complete.", line1 = "Please wait till phone is powered on or put it to flash mode manually.", line2 = "Wait for phone to be detected (see below). Then Click Continue...", line3 = "", button1 = "", button2 = "&Continue"
Showed WINDOW modal result: 2
Full bootcore version: 011302FF00000C50
Full firmware version: R452G_G_08.24.02R:GSVPEMBATMB02NA0DC
Uploading ramloader of version: 0C.50
Show WINDOW: Head = "Stage complete.", line1 = "Please wait till phone is powered on or put it to flash mode manually.", line2 = "Wait for phone to be detected (see below). Then Click Continue...", line3 = "", button1 = "", button2 = "&Continue"
Showed WINDOW modal result: 2
Show WINDOW: Head = "Stage complete.", line1 = "Your phone now is ready for the ExTestpoint stage.", line2 = "1. Make sure the USB (EMU) cable is plugged into phone and connected to the PC.", line3 = "2. Make sure the LCD is disconnected from the board.", button1 = "", button2 = "&OK"
Showed WINDOW modal result: 2
The ExTespoint's COM port is connected.
ExTP window: clicked the START (&Start) button.
ExTP window: Started enumeration sequence.
ExTP window: Power switched ON. Wait for device to enumerate...
ExTP window: Sorry, no success. Not expected bootcore version: 0C50
Comment