P5110 detect as Ti-OMAP

[grprepair]

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.56
Selected Resurrector: [Samsung P5110 XLoader+ V1.0.4773.52186]

Connecting to the target...OK
Set I/O Voltage reads as 2.60V, TCK Frequency is 8 MHz

Following devices are found on the JTAG chain:
Device on TAP #0: ID = 0x3BA00477, IR Length = 0x04 bits
Device on TAP #1: ID = 0xFFFFFFFE, IR Length = 0x06 bits
Total IR length: 0x000A bits

Analizing IDCODE(s) of the JTAG scan chain:
1. 0x3BA00477: TI OMAP4430

additional logs:

Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x0100/0x0015 (MAG2GA, 0x0003AB400000 Bytes = 14.68 GB)
Detected an Initialized FLASH2 Chip, ID: 0x0100/0x0015 (MAG2GA, 0x000000200000 Bytes = 2.00 MB)

Invalid length. It should not be zero.

Checking which Partition is blank...COMPLETE!
Following partitions are found to be completely blank:
Partition: X-LOADER at 0x000000000000
Thus in total, there is 1 blank partition.
Report Post Reply With Quote

=======================
resurrection logs:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.56
Selected Resurrector: [Samsung P5110 XLoader+ V1.0.4773.52186]

Connecting to the dead body...OK
Detected dead body ID: 0x3BA00477 - CORRECT!
Set I/O Voltage reads as 2.60V, TCK Frequency is 8 MHz

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x0100/0x0015 (MAG2GA, 0x0003AB400000 Bytes = 14.68 GB)
Detected an Initialized FLASH2 Chip, ID: 0x0100/0x0015 (MAG2GA, 0x000000200000 Bytes = 2.00 MB)

Selected Resurrection Data for the eMMC Chip with Capacity = 14.68GB

Flashing the dead body...OK
Resurrection complete!
====================

unit still detect as OMAP 4430,

tried OMAPFlash
logs:


» OMAPFlash v4.16 (Nov 4 2011)

» -v
» Entering parameter file:Targets\Projects\espresso\omap4430hs_1000MHZ. txt at li
ne: 1
» -omap 4
» -t 36000
» -p OMAP4430_1GHZ_8G_HS
» -2
» chip_download EMMC Targets\Projects\espresso\MLO
» chip_download EMMC Targets\Projects\espresso\Sbl.bin
» command cold_sw_reset
» Leaving parameter file:Targets\Projects\espresso\omap4430hs_1000MHZ. txt
» @Targets\Projects\espresso\omap4430hs_1000MHZ.txt
» Looking for device (omap usb)
» Please turn on device
» Waiting for device (omap usb)
» Found device (omap usb)
» Requesting ASIC id
» AsicId items 05
» AsicId id 01 05 01 44 30 07 04
» AsicId secure_mode 13 02 01 00
» AsicId public_id 12 15 01 A2 C8 63 C9 1E 39 FA BC 86 5E 6E 13 1A DF 4B
BA F7 6B 96 60
» AsicId root_key_hash 14 21 01 B5 85 AC F1 DD 15 B0 6A 74 81 3B FD DD 6E CD
64 22 7C E4 C9 06 58 C6 5B 4C 53 AC 22 9B 4C 6D C0
» AsicId checksum 15 09 01 9C 66 9A D9 68 2A DC CF
» Searching 2nd for: OMAP4430_1GHZ_8G_HS 443007 04 HS
» Loading second file Targets\2nd-Downloaders\dnld_startup_omap4_hs_4g_es2.s2.si
gned.2nd.hs.1GHZ
» Entering parameter filemapflash2nd.txt at line: 46
» -pheriphalboot_reopen
» Reading board configuration file Targets\Configurations\configuration_omap4430
_8g_ver416.txt
» Reading definition file .\Targets\Definitions\definitions_omap4.txt
» -board_config Targets\Configurations\configuration_omap4430_8g_v er416.txt
» Leaving parameter filemapflash2nd.txt
» Sending size of second file (0x000079B0 bytes)
» Transferring second file to target (0x79B0 bytes)
» Closing boot connection
» Waiting for device (omap usb)
» Found device (omap usb)
» Waiting for 2nd
» Error: (Unknown status message '@??????x???????x?i??????H0?x????S??x??????????
?x????Z??x?zV????????x???x????hA??????H0?xH0?x?q?x @??????xH0?x????I??xhU?xT?????
?x????????Pq?xH0?xGq?x?i??*>?x??@??q?x????d??????? ????Z??x^?M?????Gq?x?q?x???xH0
?x??@??????????????{@?H0?x??@?????H0?xL?@???????@? ') during peripheral boot (wai
ting for 2nd)
Press any key to continue . . .



» OMAPFlash v4.16 (Nov 4 2011)

» -v
» Entering parameter file:Targets\Projects\espresso\omap4430hs_1000MHZ. txt at li
ne: 1
» -omap 4
» -t 36000
» -p OMAP4430_1GHZ_8G_HS
» -2
» chip_download EMMC Targets\Projects\espresso\MLO
» chip_download EMMC Targets\Projects\espresso\Sbl.bin
» command cold_sw_reset
» Leaving parameter file:Targets\Projects\espresso\omap4430hs_1000MHZ. txt
» @Targets\Projects\espresso\omap4430hs_1000MHZ.txt
» Looking for device (omap usb)
» Please turn off device
» Please turn on device
» Waiting for device (omap usb)
» Found device (omap usb)
» Requesting ASIC id
» AsicId items 05
» AsicId id 01 05 01 44 30 07 04
» AsicId secure_mode 13 02 01 00
» AsicId public_id 12 15 01 A2 C8 63 C9 1E 39 FA BC 86 5E 6E 13 1A DF 4B
BA F7 6B 96 60
» AsicId root_key_hash 14 21 01 B5 85 AC F1 DD 15 B0 6A 74 81 3B FD DD 6E CD
64 22 7C E4 C9 06 58 C6 5B 4C 53 AC 22 9B 4C 6D C0
» AsicId checksum 15 09 01 9C 66 9A D9 68 2A DC CF
» Searching 2nd for: OMAP4430_1GHZ_8G_HS 443007 04 HS
» Loading second file Targets\2nd-Downloaders\dnld_startup_omap4_hs_4g_es2.s2.si
gned.2nd.hs.1GHZ
» Entering parameter filemapflash2nd.txt at line: 46
» -pheriphalboot_reopen
» Reading board configuration file Targets\Configurations\configuration_omap4430
_8g_ver416.txt
» Reading definition file .\Targets\Definitions\definitions_omap4.txt
» -board_config Targets\Configurations\configuration_omap4430_8g_v er416.txt
» Leaving parameter filemapflash2nd.txt
» Sending size of second file (0x000079B0 bytes)
» Transferring second file to target (0x79B0 bytes)
» Closing boot connection
» Waiting for device (omap usb)
» Found device (omap usb)
» Waiting for 2nd
==============

what possible other problem?

[grprepair]

problem was solve by trying and trying the OMAPFlasher with this result:


» OMAPFlash v4.16 (Nov 4 2011)

» -v
» Entering parameter file:Targets\Projects\espresso\omap4430hs_1000MHZ. txt at li
ne: 1
» -omap 4
» -t 36000
» -p OMAP4430_1GHZ_8G_HS
» -2
» chip_download EMMC Targets\Projects\espresso\MLO
» chip_download EMMC Targets\Projects\espresso\Sbl.bin
» command cold_sw_reset
» Leaving parameter file:Targets\Projects\espresso\omap4430hs_1000MHZ. txt
» @Targets\Projects\espresso\omap4430hs_1000MHZ.txt
» Looking for device (omap usb)
» Please turn on device
» Waiting for device (omap usb)
» Found device (omap usb)
» Requesting ASIC id
» AsicId items 05
» AsicId id 01 05 01 44 30 07 04
» AsicId secure_mode 13 02 01 00
» AsicId public_id 12 15 01 A2 C8 63 C9 1E 39 FA BC 86 5E 6E 13 1A DF 4B
BA F7 6B 96 60
» AsicId root_key_hash 14 21 01 B5 85 AC F1 DD 15 B0 6A 74 81 3B FD DD 6E CD
64 22 7C E4 C9 06 58 C6 5B 4C 53 AC 22 9B 4C 6D C0
» AsicId checksum 15 09 01 9C 66 9A D9 68 2A DC CF
» Searching 2nd for: OMAP4430_1GHZ_8G_HS 443007 04 HS
» Loading second file Targets\2nd-Downloaders\dnld_startup_omap4_hs_4g_es2.s2.si
gned.2nd.hs.1GHZ
» Entering parameter filemapflash2nd.txt at line: 46
» -pheriphalboot_reopen
» Reading board configuration file Targets\Configurations\configuration_omap4430
_8g_ver416.txt
» Reading definition file .\Targets\Definitions\definitions_omap4.txt
» -board_config Targets\Configurations\configuration_omap4430_8g_v er416.txt
» Leaving parameter filemapflash2nd.txt
» Sending size of second file (0x000079B0 bytes)
» Transferring second file to target (0x79B0 bytes)
» Closing boot connection
» Waiting for device (omap usb)
» Found device (omap usb)
» Waiting for 2nd
» Error: (Unknown status message '@??????x???????x?i??????H0?x????S??x??????????
?x????Z??x?zV????????x???x????hA??????H0?xH0?x?q?x @??????xH0?x????I??xhU?xT?????
?x????????Pq?xH0?xGq?x?i??*>?x??@??q?x????d??????? ????Z??x^?M?????Gq?x?q?x???xH0
?x??@??????????????{@?H0?x??@?????H0?xL?@???????@? ') during peripheral boot (wai
ting for 2nd)
Press any key to continue . . .

J:\GSM BOX installer and drivers\z3x files\P5110\boot>GOTO __loop

» OMAPFlash v4.16 (Nov 4 2011)

» -v
» Entering parameter file:Targets\Projects\espresso\omap4430hs_1000MHZ. txt at li
ne: 1
» -omap 4
» -t 36000
» -p OMAP4430_1GHZ_8G_HS
» -2
» chip_download EMMC Targets\Projects\espresso\MLO
» chip_download EMMC Targets\Projects\espresso\Sbl.bin
» command cold_sw_reset
» Leaving parameter file:Targets\Projects\espresso\omap4430hs_1000MHZ. txt
» @Targets\Projects\espresso\omap4430hs_1000MHZ.txt
» Looking for device (omap usb)
» Please turn off device
» Please turn on device
» Waiting for device (omap usb)
» Found device (omap usb)
» Requesting ASIC id
» AsicId items 05
» AsicId id 01 05 01 44 30 07 04
» AsicId secure_mode 13 02 01 00
» AsicId public_id 12 15 01 A2 C8 63 C9 1E 39 FA BC 86 5E 6E 13 1A DF 4B
BA F7 6B 96 60
» AsicId root_key_hash 14 21 01 B5 85 AC F1 DD 15 B0 6A 74 81 3B FD DD 6E CD
64 22 7C E4 C9 06 58 C6 5B 4C 53 AC 22 9B 4C 6D C0
» AsicId checksum 15 09 01 9C 66 9A D9 68 2A DC CF
» Searching 2nd for: OMAP4430_1GHZ_8G_HS 443007 04 HS
» Loading second file Targets\2nd-Downloaders\dnld_startup_omap4_hs_4g_es2.s2.si
gned.2nd.hs.1GHZ
» Entering parameter filemapflash2nd.txt at line: 46
» -pheriphalboot_reopen
» Reading board configuration file Targets\Configurations\configuration_omap4430
_8g_ver416.txt
» Reading definition file .\Targets\Definitions\definitions_omap4.txt
» -board_config Targets\Configurations\configuration_omap4430_8g_v er416.txt
» Leaving parameter filemapflash2nd.txt
» Sending size of second file (0x000079B0 bytes)
» Transferring second file to target (0x79B0 bytes)
» Closing boot connection
» Waiting for device (omap usb)
» Found device (omap usb)
» Waiting for 2nd

then battery logo charging appears and I can enter flash mode.