Announcement

Collapse
No announcement yet.

New Version ZTE S 183_ RIC_S183_RBTL21FV1 0 0B07 Problem

Collapse
X
Collapse
 
  • Page of 2
  • Filter
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • #1

    New Version ZTE S 183_ RIC_S183_RBTL21FV1 0 0B07 Problem

    Dear Legija ,
    I have 52 Set ZTE S 183 Dead (Version RIC_S183_RBTL21FV1 0 0B07) Durring unlock
    write Working Set Dump but Set not Power on

    here is logs

    open serial port...OK
    Connecting to the RIFF Box...OK Firmware Version: 1.37, JTAG Manager Version: 1.56
    Selected Resurrector: [ZTE S183 V1.0.5162.54298]

    Connecting to the dead body...OK
    Detected dead body ID: 0x122C80E1 - CORRECT!
    Set I/O Voltage reads as 1.80V, TCK Frequency is RTCK
    Adaptive Clocking RTCK Sampling is: [Sample at MAX]
    Settings Code: 0x24010000000000000000000001000000
    Resurrection sequence started.
    Establish communication with the phone...OK
    Initializing internal hardware configuration...OK
    Uploading resurrector data into memory...OK
    Starting communication with resurrector...OK

    Detected an Initialized FLASH1 Chip, ID: 0x017E/0x0065 (16MB)
    Resuming write FLASH1 memory from 0x000000000000 to 0x000000FFFFFF on 0x000000380000
    ERROR: DCC Loader has reported Error Code = 0x2B (0x000000). Trying to recover...OK
    ERROR: DCC Loader has reported Error Code = 0x2B (0x000000). Trying to recover...OK
    Completed in 00:07:25.359 (Average Transfer Rate: 36.79 kB/s)
    FINISH OPERATION_ID = DCC_WRITE_MEMORY]
    Dump Working Set
    ZTE S 183_ RIC_S183_RBTL21FV1 0 0B07

    Need Help Sir
    Tags: None
  • #2
    Yaaa Riff team u need to find out solution.

    Comment

    • #3
      zte s183 dead by riff during unlock

      Open serial port...OK
      Connecting to the RIFF Box...OK
      Firmware Version: 1.37, JTAG Manager Version: 1.56
      Selected Resurrector: [ZTE S183 V1.0.5165.40995]
      Restarting target (nRST Low then High)...OK

      Connecting to the dead body...OK
      Detected dead body ID: 0x122C80E1 - CORRECT!
      Set I/O Voltage reads as 1.79V, TCK Frequency is RTCK
      Adaptive Clocking RTCK Sampling is: [Sample at MAX]
      Settings Code: 0x20010000000000000000000001000000

      Resurrection sequence started.
      Establish communication with the phone...OK
      Initializing internal hardware configuration...OK
      Uploading resurrector data into memory...OK
      Starting communication with resurrector...OK

      Detected an Initialized FLASH1 Chip, ID: 0x017E/0x0065 (16MB)

      Writting FLASH1 memory from 0x000000000000 to 0x000000FFFFFF
      ERROR: Timeout while waiting for DCC Loader response. Trying to recover...FAILED
      ERROR: Failed due to multiple communication errors. Terminating at 0x000000000000


      Open serial port...OK
      Connecting to the RIFF Box...OK
      Firmware Version: 1.37, JTAG Manager Version: 1.56
      Selected Resurrector: [ZTE S183 V1.0.5165.40995]

      Connecting to the target...OK
      Set I/O Voltage reads as 1.80V, TCK Frequency is RTCK

      Following devices are found on the JTAG chain:
      Device on TAP #0: ID = 0x122C80E1, IR Length = 0x04 bits
      Total IR length: 0x0004 bits

      Analizing IDCODE(s) of the JTAG scan chain:
      1. 0x122C80E1: Qualcomm QSC1110, H/W Rev. #1

      Comment

      • #4
        Market have two type ZTE S183 first 8mb flash file and second 16mb flash file have.

        always 16mb version does not repair with RIFF.

        Comment

        • #5
          Open serial port...OK
          Connecting to the RIFF Box...OK
          Firmware Version: 1.37, JTAG Manager Version: 1.56
          Selected Resurrector: [ZTE S183 V1.0.5162.54298]

          Connecting to the dead body...OK
          Detected dead body ID: 0x122C80E1 - IGNORED!
          Set I/O Voltage reads as 1.79V, TCK Frequency is RTCK
          Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz]
          Settings Code: 0x24010009000000000000000001000000

          Resurrection sequence started.
          Establish communication with the phone...OK
          Initializing internal hardware configuration...OK
          Uploading resurrector data into memory...OK
          Starting communication with resurrector...OK

          Detected an Initialized FLASH1 Chip, ID: 0x017E/0x0063 (16MB)

          Writting FLASH1 memory from 0x000000000000 to 0x000000FFFFFF
          ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK
          ERROR: Forced to Terminate. Terminated at 0x000000000000

          Comment

          • #6
            Originally posted by ravi mobile View Post
            Open serial port...OK
            Connecting to the RIFF Box...OK
            Firmware Version: 1.37, JTAG Manager Version: 1.56
            Selected Resurrector: [ZTE S183 V1.0.5162.54298]

            Connecting to the dead body...OK
            Detected dead body ID: 0x122C80E1 - IGNORED!
            Set I/O Voltage reads as 1.79V, TCK Frequency is RTCK
            Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz]
            Settings Code: 0x24010009000000000000000001000000

            Resurrection sequence started.
            Establish communication with the phone...OK
            Initializing internal hardware configuration...OK
            Uploading resurrector data into memory...OK
            Starting communication with resurrector...OK

            Detected an Initialized FLASH1 Chip, ID: 0x017E/0x0063 (16MB)

            Writting FLASH1 memory from 0x000000000000 to 0x000000FFFFFF
            ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK
            ERROR: Forced to Terminate. Terminated at 0x000000000000

            yes my problem is same .....

            plz help sir ,,,,,,,,

            Comment

            • #7
              ok sir

              Comment

              • #8
                asus nexus 7

                how to repair dead boot asus nexus 7 tab. thanks

                Comment

                • #9
                  zte s183 call failed

                  hello friends i have flash but always call failed

                  Comment

                  • #10
                    call failed solution s183

                    please provide me s183 call failed solution

                    Comment

                    • #11
                      legije waitting new update

                      Comment

                      • #12
                        Sir Waiting For ur reply

                        Comment

                        • #13
                          sir please give solution

                          Comment

                          • #14
                            Open serial port...OK
                            Connecting to the RIFF Box...OK
                            Firmware Version: 1.39 (RIFFBOX1), JTAG Manager Version: 1.59
                            Selected Resurrector: [ZTE S183 V1.0.5165.40995]

                            Connecting to the dead body...OK
                            Detected dead body ID: 0x122C80E1 - CORRECT!
                            Set I/O Voltage reads as 1.79V, TCK Frequency is 1 MHz

                            Resurrection sequence started.
                            Establish communication with the phone...OK
                            Initializing internal hardware configuration...OK
                            Uploading resurrector data into memory...OK
                            Starting communication with resurrector...OK

                            Detected an Initialized FLASH1 Chip, ID: 0x017E/0x0061 (8MB)
                            WARNING: No Data for the current NOR Chip. Selected default Data for the NOR Chip with IDs: 0x017E/0x0063

                            Flashing the dead body...
                            ERROR: Timeout while waiting for DCC Loader response. Trying to recover...FAILED
                            ERROR: Failed due to multiple communication errors. Terminating at 0x000000000000

                            Comment

                            • #15
                              Open serial port...OK
                              Connecting to the RIFF Box...OK
                              Firmware Version: 1.39 (RIFFBOX1), JTAG Manager Version: 1.59
                              Selected Resurrector: [ZTE S183 V1.0.5165.40995]
                              Connecting to the dead body...OK
                              Detected dead body ID: 0x122C80E1 - CORRECT!
                              Set I/O Voltage reads as 1.79V, TCK Frequency is RTCK
                              Adaptive Clocking RTCK Sampling is: [Sample at MAX]
                              Settings Code: 0x26010000000000000000000000800000
                              Resurrection sequence started.
                              Establish communication with the phone...OK
                              Initializing internal hardware configuration...OK
                              Uploading resurrector data into memory...OK
                              Starting communication with resurrector...OK
                              Detected an Initialized FLASH1 Chip, ID: 0x017E/0x0061 (8MB)
                              Resuming write FLASH1 memory from 0x000000000000 to 0x0000007FFFFF on 0x000000000000
                              ERROR: Timeout while waiting for DCC Loader response. Trying to recover...FAILED
                              ERROR: Failed due to multiple communication errors. Terminating at 0x000000000000

                              Comment

                              Previous 1 2 template Next
                              Working...
                              X

                              We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.

                              By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.

                              I Agree