Code for Blaupunkt 2020 / Holden Barina

Hey,
same situation as the others, changed the battery and dont have the code.
Car: Holden Barina Hatchback
Radio: Blaupunkt 2020
No: 92 094 577
Serial: BP248531305301

unfortunately the screen in the dash board does not work, making it hard to put in the code. So i was woundering if someone could post up the steps so i can put the code in.
help much appreciated

As I mentioned in my previous point I had already pointed that out, but just wanted to put it in for reference's sake.

[RegWorts]

As Reg mentioned you need to provide all those details. I don't know whether mine will work with yours but here ya go in case you want to try. 5510.

Yes lummie , your code does calculate to 5510 using the info on your uploaded photo....but this code will only work on your radio...and no-one elses. .

Would you be able to tell me the code?

As Reg mentioned you need to provide all those details. I don't know whether mine will work with yours but here ya go in case you want to try. 5510.

[RegWorts]

Would you be able to tell me the code?

Post the radio MAKE+MODEL plus ALL the NUMBERS+LETTERS on ANY LABELS , BARCODES or STAMPED IN THE METAL CASING

Would you be able to tell me the code?

Well I managed to get the code off another forum so its all working again. Thank you everyone for all your help in accessing my car radio. I couldn't have done it without you!!

Finally! I was able to get the damn deck out. By complete surprise after ages of fiddling it just popped right out!! arty:

So here is the picture of what I found



Just to confirm
Car: Holden Barina Hatchback
Radio: Blaupunkt 2020
No: 92 094 577
Serial: BP0485 1 7819281

Thanks!!! :thumbsup:

Ok so I had to guy purchase an allen key for the size of the hole but that explained why I was having so little success with the wire method.

Unfortunately I have tried screws, coathanger wire and can't seem to yank it out. It just seems to be wedged in and with the coathanger wire it just bends. Is there any particular method like when you insert the wire or pins. In one of the instructions it said about putting coathanger wire a bit upwards towards the stereo. It would latch on and pull out. No luck it just bends the wire.

Do I need some strong nails or something?

Just another pic without the screws in place.

[RegWorts]

Yes, they look like small hexagonal heads so you will need the appropriate size of Allen key to unscrew them....before using your "coathanger" extractor

Ok I tried again this afternoon but am not sure if its because I need to use some sort of allen key on it? I took some pictures to see if that would help.

Okay, will look out for these screws. I think it was just the coathanger ends were a little large but will give it another try. Thanks again

[RegWorts]

Can I just ask, I tried this link and I have tried two different coathangers and can't seem to get them in. Too wide in diameter. Is there a particular type of coathanger to use? Its also quite hard to know where to bend to get both sides even.

Ohh these damn radios.

Anyway any help would be greatly appreciated.

If the holes appear to be blocked, then they might be protected by four small screws with Allen Key heads.(or similar tamper proof heads).If so , unscrew using the appropriate sized Allen Key.

Using the coathanger method is fiddly but it does work with a bit of patience.

You could also use 4 x nails...or 4 x darts....or 4 x small screwdrivers ...or 4 x small Allen keys.....etc. etc.

Having an assistant to help is also useful.

Can I just ask, I tried this link and I have tried two different coathangers and can't seem to get them in. Too wide in diameter. Is there a particular type of coathanger to use? Its also quite hard to know where to bend to get both sides even.

Ohh these damn radios.

Anyway any help would be greatly appreciated.

Thanks

Try 2973

If this fails to work, please quote the MAKE of CAR it is fitted into.

Thanks RegWorts, that worked! Appreciate the prompt reply.