RIFF1 JTAG Manager 1.74 firmware 1.48 update Samsung EMMC firmware error

[den7497427]

Hello. I have RIFF1 after updating to RIFF JTAG Manager 1.74 firmware 1.48 does not restore Samsung EMMC. I have one such problem? Samsung format it does, and update
EMMC firmware is not present - writes failure and after that Samsung format does not do any more, i.e. actually kills EMMC. Tried on both RJ45 and JTAG. please tell
me how to solve this problem? I did not fulfill several orders because of this.

[den7497427]

[21.11.2017 0:51:59] [START OPERATION_ID = 38]
[21.11.2017 0:53:07] Открытие порта...OK
[21.11.2017 0:53:07] Подключение к RIFF Боксу...OK
[21.11.2017 0:53:07] Версия Прошивки: 1.48 (RIFFBOX1), Версия JTAG Manager: 1.74
[21.11.2017 0:53:07]
[21.11.2017 0:53:07] Connecting to the SD/eMMC Card...OK
[21.11.2017 0:53:07] Выставленное I/O Напряжение 3.30V, SD_CLK Frequency is 1 MHz
[21.11.2017 0:53:07]
[21.11.2017 0:53:07] Detected eMMC Chip, ID: 0x15/0x00 (000000), User Area Partition = 0x000400000000 Bytes (16.00 GB)
[21.11.2017 0:53:07]
[21.11.2017 0:53:07]
[21.11.2017 0:53:07] Preparing eMMC Core F/W Update...OK (Завершено за 00:39.110)
[21.11.2017 0:53:07] Uploading eMMC Core Firmware Data...СБОЙ
[21.11.2017 0:53:07] [FINISH OPERATION_ID = 38]

[21.11.2017 0:48:50] [START OPERATION_ID = 38]
[21.11.2017 0:49:34] Открытие порта...OK
[21.11.2017 0:49:34] Подключение к RIFF Боксу...OK
[21.11.2017 0:49:34] Версия Прошивки: 1.48 (RIFFBOX1), Версия JTAG Manager: 1.74
[21.11.2017 0:49:34]
[21.11.2017 0:49:34] Connecting to the SD/eMMC Card...OK
[21.11.2017 0:49:34] Выставленное I/O Напряжение 3.30V, SD_CLK Frequency is 1 MHz
[21.11.2017 0:49:34]
[21.11.2017 0:49:34] Detected eMMC Chip, ID: 0x15/0x00 (MAG2GA), User Area Partition = 0x000400000000 Bytes (16.00 GB)
[21.11.2017 0:49:34]
[21.11.2017 0:49:34]
[21.11.2017 0:49:34] Preparing eMMC Core F/W Update...OK (Завершено за 00:39.218)
[21.11.2017 0:49:34] Uploading eMMC Core Firmware Data...СБОЙ
[21.11.2017 0:49:34] [FINISH OPERATION_ID = 38]

[olegas6]

The situation is similar,when writing fw riffboxv1 died 2 emmc + emmc not detected via jtag connector on the pin clk the frequency above 200khz is not raised

[den7497427]

Legia please do something. I have problems with clients because of this situation. Is it possible to return to 1.47?

[Legija]

Possible, but we're short with time today. I still don't understand exactly whats the problem, though.

[den7497427]

If necessary, I will provide you with any details. The problem is that in RIFF 1 on PJ45 and JTAG ports it is impossible to recover the EMMC Samsung. I ask you to roll back to the old version of the RIFF box firmware, or to fix the malfunction in the new version so that the possibility of restoring the EMMC SAMSUNG appears. On this depends the fulfillment of many orders in my master

[Legija]

In some of the previous versions of JTAG Manager, is introduced drop down menu on eMMC advanced page - to select between standard JEDEC functions and customized Samsung functions.
It's possible that something was lost here, because now automatic detection is disabled (some samsung custom commands caused boot 2 partition erasure).

This topic is passed to RIFF developer, so any information You have is monitored.

[den7497427]

The fact is that in the version where the dropdown menu appeared JEDEC - Samsung, recovery EMMC Samsung still worked. The problem appeared on the JTAG Manager version 1.74 firmware 1.48

[Roer]

Hi.
I have the same problem.
After updating 1.74 when trying to write firmware emmc, the connection with the box is broken for a few seconds and
"Uploading eMMC Core Firmware Data ... FAIL"
Also noticed frequent breaks in communication with the box when working with other tabs, I need to reconnect usb.

[Legija]

Hi.
I have the same problem.
After updating 1.74 when trying to write firmware emmc, the connection with the box is broken for a few seconds and
"Uploading eMMC Core Firmware Data ... FAIL"
Also noticed frequent breaks in communication with the box when working with other tabs, I need to reconnect usb.

Which box version You have there ? V1 or v2 ?

[Roer]

riff v1
here i add the example of firmware, readed from damaged emmc.
Unlock Forum - RIFF Box support forum

[Legija]

riff v1
here i add the example of firmware, readed from damaged emmc.
Unlock Forum - RIFF Box support forum

Thanks.

I hope fix will come soon, for now don't try updating emmc controller firmware again

[Roer]

ok, thanks

[Roer]

Hello.
What to expect in the near future?
What news?

[den7497427]

Update has been released. Thanks Legija.