Panasonic Eluga L2 9008 mode?

[ajubaba]

Dear All,




Panasonic Eluga L2 dead due to wrong flash, now in qualcomm 9008 mode.




Things done so far:


1) Connected to Riff with MSM8916->Generic eMMC loader 2


2) Under USB read/write->check memory

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.51 (RIFFBOX1), JTAG Manager Version: 1.82
Selected Manual Mode: [Qualcomm SAHARA, Generic eMMC Loader 2]

Connecting to the Device via USB Interface...OK
Uploading the USB Loader into Device Memory...OK

Initializing Communication via Qualcomm Firehose Protocol...OK

Memory Type .......................... eMMC
User Area Partition Size ............. 0x0001D2000000 Bytes (7.28 GB)
Boot Partition Size .................. 0x000000400000 Bytes (4.00 MB)

3) Found CM2 readed firmware

Just a moment...

Is there any possibilities through riff?


Please help


Best Regards
~Aju

[Legija]

Hi,
Can You please upload firehose loader which worked in this phone ?
I'll prepare repair package in that case.


edit:
Sorry havent read carefully, I see You've used embedded loader.
>Let me see if there is factory stock rom for this model to download.

[Legija]

Panasonic_Eluga_L2.riffpkg
Save file to "RepairPacks" folder. Start JTAG Manager, select Panasonic Eluga L2.
On USB TAB click "Check Memory" and after successful connection start eMMC Plugin (Useful Plugins -> eMMC based fullflash plugin).


Click "Parse official firmware" and select "Rawprogram0.xml" from extracted firmware folder.
Click "Flash selected used". After flashing is finished, click "Parse connected memory" and "Adjust GPT for current chip".


Factory firmware download:





AndroidFileHost.com | Download GApps, Roms, Kernels, Themes, Firmware and more. Free file hosting for all Android developers.

[ajubaba]

Panasonic_Eluga_L2.riffpkg
Save file to "RepairPacks" folder. Start JTAG Manager, select Panasonic Eluga L2.
On USB TAB click "Check Memory" and after successful connection start eMMC Plugin (Useful Plugins -> eMMC based fullflash plugin).


Click "Parse official firmware" and select "Rawprogram0.xml" from extracted firmware folder.
Click "Flash selected used". After flashing is finished, click "Parse connected memory" and "Adjust GPT for current chip".


Factory firmware download:





AndroidFileHost.com | Download GApps, Roms, Kernels, Themes, Firmware and more. Free file hosting for all Android developers.

Thanks for your package.



I tried it but charging light appears for a while and again it goes to Qualcomm Mode.


Best Regards
~Aju

[Legija]

Please read 128mb from user area partition, and uplod here.
Also, check battery level.

[ajubaba]

Please read 128mb from user area partition, and uplod here.
Also, check battery level.

Here it is 128mb from user area partition


Best regards


~Aju

[Legija]

Ok, thank You.
I don't see anything wrong with this dump.


Logic says that if charging lights came up, bootchain was alive in phone, otherwise it would not show anything.
It's quite possible that battery is depleted bellow threshold, some qualcomm phones would enumerate as "usb input device" in that case.


Have You measured battery level ?

[ajubaba]

Ok, thank You.
I don't see anything wrong with this dump.


Logic says that if charging lights came up, bootchain was alive in phone, otherwise it would not show anything.
It's quite possible that battery is depleted bellow threshold, some qualcomm phones would enumerate as "usb input device" in that case.


Have You measured battery level ?

Battery was completely exhausted. Replaced and working. Thanks Riff


Best Regards
~Aju