Oppo a3s dead,!!!!

[Legija]

There is repair bootloader option, You can use it.

However, I do not recommend it, at least not before making backup. I am 100% positive that Your phone has hardware fault (of course if You did not do anything else but wipe data).

To write full backup would take too much time with old RIFF because of slow speed. I'm not even sure full backup exists.

Bootloader repair will enable phone to enter recovery (if hw is not damaged) , from where You can flash ozip file.

[med9306]

not qualcomm usb i power phone vibrate only

[Legija]

What is your phone exact model ? And what you have done now so phone vibrates ?

[med9306]

oppo a3s i writing dump from another phone

[Legija]

Oppo A3s has few variants, You need to know exact CPH model.

[med9306]

cph1803

[Legija]

Link


You can download CPH1803 extracted firmware, and flash it using eMMC Plugin. It's very slow with old box, but possibly can help if You can't get anything faster.


After flashing, GPT needs to be adjusted.
eMMC plugin -> Parse official firmware -> raprogram0.xml -> flash selected used.

[med9306]

2 oppo cph 1803 after resset password is dead
is not problem hardware

[med9306]

si possble restore Backup Files with riff

[Legija]

Backup files created only if reset is done via eMMC/UFS partition plugin.


I think You probably selected wrong model and used reset from resurrection TAB. To see what exactly You did, you need to upload your jtagmanager.txt file here and post exact date when You made reset on phone.

[yanzznagma]

cph 1823 canot find da agent

[med9306]

[04/12/2019 19:54:26] Memory Type: eMMC
[04/12/2019 19:54:26] Manufacturer ID: 0x15 (SAMSUNG)
[04/12/2019 19:54:26] OEM/Application ID: 0x00
[04/12/2019 19:54:26] Product Name: "QE63MB"
[04/12/2019 19:54:26] Package: BGA
[04/12/2019 19:54:26]
[04/12/2019 19:54:26] Memory Capacity and Geometry Info
[04/12/2019 19:54:26]
[04/12/2019 19:54:26] User Area Partition Size ............. 0x0003A3E00000 Bytes (14.56 GB)
[04/12/2019 19:54:26] Boot Partition Size .................. 0x000000400000 Bytes (4.00 MB)
[04/12/2019 19:54:26] RPMB Partition Size .................. 0x000000400000 Bytes (4.00 MB)
[04/12/2019 19:54:26] OCR Register ......................... 0xC0FF8080 (Dual Voltage, High Capacity)
[04/12/2019 19:54:26] CID Register ......................... 150100514536334D4203A9EBD2AEA595
[04/12/2019 19:54:26] CSD Register ......................... D02701320F5903FFF6DBFFEF8E40400D
[04/12/2019 19:54:26] Write Protection Bits ................ NONE
[04/12/2019 19:54:26] ExtCSD Register Fields ............... [177] = 0x00, [179] = 0x38, [162] = 0x01
[04/12/2019 19:54:26] Boot Configuration ................... Boot from User Area (Bus Width = 1 Bit)
[04/12/2019 19:54:26] Chip Revision ........................ 0.3
[04/12/2019 19:54:26] Multimedia Card Revision ............. 1.8 (eMMC v5.1)
[04/12/2019 19:54:26] Serial Number ........................ 0xA9EBD2AE
[04/12/2019 19:54:26] Memory Manufacturing Date ............ November, 2018
[04/12/2019 19:54:26]
[04/12/2019 19:54:26] Memory Health Information
[04/12/2019 19:54:26]
[04/12/2019 19:54:26] Device life time reflected by Reserved Blocks - NORMAL
[04/12/2019 19:54:26] Estimated wear out of MLC Memory - Wear out: 10%..20%, Lifetime remaining: 80%..90%
[04/12/2019 19:54:26] Estimated wear out of SLC Memory - Wear out: 10%..20%, Lifetime remaining: 80%..90%
[04/12/2019 19:54:26] [FINISH OPERATION_ID = 26]

[04/12/2019 19:54:30] [START OPERATION_ID = RESURRECT]
[04/12/2019 19:54:40] Open serial port...OK
[04/12/2019 19:54:40] Connecting to the RIFF Box...OK
[04/12/2019 19:54:40] Firmware Version: 1.53 (RIFFBOX1), JTAG Manager Version: 1.87
[04/12/2019 19:54:40] Selected Package: [Oppo A3s CPH1803 V1.09 by <legija>, <RJ-45>, 1 Bit Bus Width (DAT0)]
[04/12/2019 19:54:40]
[04/12/2019 19:54:40] Connecting to the SD/eMMC Card...OK
[04/12/2019 19:54:40] WARNING: Embedded I/O Voltage is overriden to 1.80V
[04/12/2019 19:54:40] Set I/O Voltage reads as 1.79V, SD_CLK Frequency is 490 KHz
[04/12/2019 19:54:40]
[04/12/2019 19:54:40] Detected eMMC Chip, ID: 0x15/0x00 (QE63MB), User Area Partition = 0x0003A3E00000 Bytes (14.56 GB)
[04/12/2019 19:54:40]
[04/12/2019 19:54:40] Writting to the SD/MMC Card...OK
[04/12/2019 19:54:40] Package execution complete!
[04/12/2019 19:54:40] [FINISH OPERATION_ID = RESURRECT]

[med9306]

I am sure model cph1803

[Legija]

This is log from yesterday ?

Please read 1MB from user area and upload here.
Start: 0x0000 0000 0000
Data Length: 0x0000 00010 0000

[med9306]

cph1803.rar
thank you