i tried to unlock v3redge using tp cable but always error.
here is log.
Wait for TCI started.
Established connection to: \\.\Motorola USB Modem #3
Checking connected interface: Motorola Accessory
Checking connected interface: Motorola MCU Data Logger
Checking connected interface: Motorola Test Command
Waiting for flash interface init...
Clicked button: UNLOCK (&Stop)
Clicked button: UNLOCK (&Unlock)
On WIZARD clicked: CONTINUE button
On WIZARD accepted port: COM8
Wait for TCI started.
Established connection to: \\.\Motorola USB Modem #3
Checking connected interface: Motorola Accessory
Checking connected interface: Motorola MCU Data Logger
Checking connected interface: Motorola Test Command
Waiting for flash interface init...
Detected motorola interface: Motorola Flash
Full bootcore version: 011302FF00000CC1
Full firmware version: R3442A_G_0E.41.22R:GSVV3XX060RTGB0DB
Decision: bootcore flashing needed.
The ExTespoint's COM port is connected.
Full bootcore version: 011302FF00000CC1
Full firmware version: R3442A_G_0E.41.22R:GSVV3XX060RTGB0DB
Uploading ramloader of version: 0C.C0
Reading 131072 bytes...
Reading 262144 bytes...
Reading 131072 bytes...
Show WINDOW: Head = "Stage complete.", line1 = "Please wait till phone is powered on or put it to flash mode manually.", line2 = "Wait for phone to be detected (see below). Then Click Continue...", line3 = "", button1 = "", button2 = "&Continue"
Showed WINDOW modal result: 2
Full bootcore version: 011302FF00000CC1
Full firmware version: R3442A_G_0E.41.22R:GSVV3XX060RTGB0DB
Uploading ramloader of version: 0C.C0
Show WINDOW: Head = "Stage complete.", line1 = "Please wait till phone is powered on or put it to flash mode manually.", line2 = "Wait for phone to be detected (see below). Then Click Continue...", line3 = "", button1 = "", button2 = "&Continue"
Showed WINDOW modal result: 2
Show WINDOW: Head = "Stage complete.", line1 = "Your phone now is ready for the ExTestpoint stage.", line2 = "1. Make sure the USB (EMU) cable is plugged into phone and connected to the PC.", line3 = "2. Make sure the LCD is disconnected from the board.", button1 = "", button2 = "&OK"
Showed WINDOW modal result: 2
The ExTespoint's COM port is connected.
ExTP window: selected handsfree timeout - "10 Seconds timeout"
ExTP window: clicked the START (&Start) button.
ExTP window: Started enumeration sequence.
ExTP window: Power switched ON. Wait for device to enumerate...
ExTP window: Sorry, no success. Not expected bootcore version: 0CC1
ExTP window: clicked the START (&Start) button.
ExTP window: Started enumeration sequence.
ExTP window: Power switched ON. Wait for device to enumerate...
ExTP window: ExTP worked, starting booting...
Full bootcore version: 011302FF00000000
Phone serial number: 25A014100D0E091B9A1311619245F002
Uploading ramloader of version: custom ramloader used.
Phone is booted with ExTestpoint. Flash ID: 0B208818
Flash ID: 0020 8818, SCC status: 09
Unlocking error
here is log.
Wait for TCI started.
Established connection to: \\.\Motorola USB Modem #3
Checking connected interface: Motorola Accessory
Checking connected interface: Motorola MCU Data Logger
Checking connected interface: Motorola Test Command
Waiting for flash interface init...
Clicked button: UNLOCK (&Stop)
Clicked button: UNLOCK (&Unlock)
On WIZARD clicked: CONTINUE button
On WIZARD accepted port: COM8
Wait for TCI started.
Established connection to: \\.\Motorola USB Modem #3
Checking connected interface: Motorola Accessory
Checking connected interface: Motorola MCU Data Logger
Checking connected interface: Motorola Test Command
Waiting for flash interface init...
Detected motorola interface: Motorola Flash
Full bootcore version: 011302FF00000CC1
Full firmware version: R3442A_G_0E.41.22R:GSVV3XX060RTGB0DB
Decision: bootcore flashing needed.
The ExTespoint's COM port is connected.
Full bootcore version: 011302FF00000CC1
Full firmware version: R3442A_G_0E.41.22R:GSVV3XX060RTGB0DB
Uploading ramloader of version: 0C.C0
Reading 131072 bytes...
Reading 262144 bytes...
Reading 131072 bytes...
Show WINDOW: Head = "Stage complete.", line1 = "Please wait till phone is powered on or put it to flash mode manually.", line2 = "Wait for phone to be detected (see below). Then Click Continue...", line3 = "", button1 = "", button2 = "&Continue"
Showed WINDOW modal result: 2
Full bootcore version: 011302FF00000CC1
Full firmware version: R3442A_G_0E.41.22R:GSVV3XX060RTGB0DB
Uploading ramloader of version: 0C.C0
Show WINDOW: Head = "Stage complete.", line1 = "Please wait till phone is powered on or put it to flash mode manually.", line2 = "Wait for phone to be detected (see below). Then Click Continue...", line3 = "", button1 = "", button2 = "&Continue"
Showed WINDOW modal result: 2
Show WINDOW: Head = "Stage complete.", line1 = "Your phone now is ready for the ExTestpoint stage.", line2 = "1. Make sure the USB (EMU) cable is plugged into phone and connected to the PC.", line3 = "2. Make sure the LCD is disconnected from the board.", button1 = "", button2 = "&OK"
Showed WINDOW modal result: 2
The ExTespoint's COM port is connected.
ExTP window: selected handsfree timeout - "10 Seconds timeout"
ExTP window: clicked the START (&Start) button.
ExTP window: Started enumeration sequence.
ExTP window: Power switched ON. Wait for device to enumerate...
ExTP window: Sorry, no success. Not expected bootcore version: 0CC1
ExTP window: clicked the START (&Start) button.
ExTP window: Started enumeration sequence.
ExTP window: Power switched ON. Wait for device to enumerate...
ExTP window: ExTP worked, starting booting...
Full bootcore version: 011302FF00000000
Phone serial number: 25A014100D0E091B9A1311619245F002
Uploading ramloader of version: custom ramloader used.
Phone is booted with ExTestpoint. Flash ID: 0B208818
Flash ID: 0020 8818, SCC status: 09
Unlocking error
Comment