Announcement

Collapse
No announcement yet.

Zte c132 (S183 ) mts.c132.b05 support request

Collapse
X
Collapse
 
  • Page of 2
  • Filter
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • #1

    Zte c132 (S183 ) mts.c132.b05 support request

    ZTE C132 MTS.C132.B05 SUPPORT REQUEST

    Checking Firmware Version...

    FOUND 16MB ZTE SSTL_S183_NL_RBTL40NV1.0.0B02...

    4shared - free file sharing and storage

    FLASH *983*9529# flash type SPANSION S71VS128RCD CPU:ARM9 (QSC1110)

    *983*636# RAM RAM TOTAL: 1.859MB RAM FREE: 1.124MB

    *983*33837# COMPILE TIME NOV 13 2013 19:01:55

    *983*26*75# inner version sstl_s183_NL_RBTL40NV1.0.0B02

    *983*154# sw ver all

    c132 new ver b05 ok set
    Open serial port...OK
    Connecting to the RIFF Box...OK
    Firmware Version: 1.37, JTAG Manager Version: 1.55
    Selected Resurrector: [ZTE S165 V1.0.4609.43971]
    Restarting target (nRST Low then High)...OK

    Connecting to the dead body...OK
    Detected dead body ID: 0x122C80E1 - IGNORED!
    Set I/O Voltage reads as 1.79V, TCK Frequency is RTCK
    Adaptive Clocking RTCK Sampling is: [Sample at MAX]
    Settings Code: 0x36010000000000000000000001000000

    Resurrection sequence started.
    Establish communication with the phone...OK
    Initializing internal hardware configuration...OK
    Uploading resurrector data into memory...OK
    Starting communication with resurrector...OK

    Detected an Initialized FLASH1 Chip, ID: 0x0001/0x007E (16MB)

    Reading FLASH1 address space from 0x000000000000 to 0x000000FFFFFF

    set on reading ok
    write faild

    any way to write dump sir

    sir i think write protected

    Open serial port...OK
    Connecting to the RIFF Box...OK
    Firmware Version: 1.37, JTAG Manager Version: 1.55
    Selected Resurrector: [ZTE S165 V1.0.4609.43971]
    Restarting target (nRST Low then High)...OK

    Connecting to the dead body...OK
    Detected dead body ID: 0x122C80E1 - IGNORED!
    Set I/O Voltage reads as 1.79V, TCK Frequency is RTCK
    Adaptive Clocking RTCK Sampling is: [Sample at MAX]
    Settings Code: 0x16010000000000000000000001000000

    Resurrection sequence started.
    Establish communication with the phone...OK
    Initializing internal hardware configuration...OK
    Uploading resurrector data into memory...OK
    Starting communication with resurrector...OK

    Detected an Initialized FLASH1 Chip, ID: 0x0001/0x007E (16MB)

    Erasing FLASH1 memory from 0x000000000000 to 0x000000FFFFFF...ERROR
    Failed to Receive answer to ERASE command.

    I WILL TAKE A PICTURE SOON
    Tags: None
  • #2
    Photos of pcb c132

    Photos of pcb c132

    Comment

    • #3
      how to unlock new ver zte c s183

      sir how to unlock zte c s183 ko pls file post

      Comment

      • #4
        plz legija update this

        Comment

        • #5
          s183 in hand but i no know version becose set blinking mode also i have read full flash file s183 16mb working set but writting,earsing problem,redding perfect
          Just a moment...

          Comment

          • #6
            We need users today to finish beta tests, if You have such phone please contact me via ICQ.
            ICQ: 299-912-089
            QQ: 1634811353

            Comment

            • #7
              Here is S183 DLL for tests:
              ICQ: 299-912-089
              QQ: 1634811353

              Comment

              • #8
                Alatel C131 Done With ths Dll

                Open serial port...OK
                Connecting to the RIFF Box...OK
                Firmware Version: 1.37, JTAG Manager Version: 1.55
                Selected Resurrector: [ZTE S183 V1.0.5162.54298]

                Connecting to the dead body...OK
                Detected dead body ID: 0x122CE0E1 - IGNORED!
                Set I/O Voltage reads as 1.79V, TCK Frequency is RTCK
                Adaptive Clocking RTCK Sampling is: [Sample at MAX]
                Settings Code: 0x34010000000000000000000001000000

                Resurrection sequence started.
                Establish communication with the phone...OK
                Initializing internal hardware configuration...OK
                Uploading resurrector data into memory...OK
                Starting communication with resurrector...OK

                Detected an Initialized FLASH1 Chip, ID: 0x017E/0x0063 (16MB)

                Resuming write FLASH1 memory from 0x000000000000 to 0x000000FFFFFF on 0x000000380000
                WARNING: Programming Error (0x25) at 0x000000FE0000. Attempting to Repeat.
                WARNING: Programming Error (0x25) at 0x000000FE0000 is Ignored.
                WARNING: Programming Error (0x25) at 0x000000FF0000 is Ignored.
                Completed in 00:05:06.657 (Average Transfer Rate: 53.43 kB/s)

                Comment

                • #9
                  ZTE S183 Done

                  Open serial port...OK
                  Connecting to the RIFF Box...OK
                  Firmware Version: 1.37, JTAG Manager Version: 1.55
                  Selected Resurrector: [ZTE S183 V1.0.5162.54298]
                  Connecting to the dead body...OK
                  Detected dead body ID: 0x122C80E1 - CORRECT!
                  Set I/O Voltage reads as 1.80V, TCK Frequency is RTCK
                  Adaptive Clocking RTCK Sampling is: [Sample at MAX]
                  Settings Code: 0x24010000000000000000000000800000
                  Resurrection sequence started.
                  Establish communication with the phone...OK
                  Initializing internal hardware configuration...OK
                  Uploading resurrector data into memory...OK
                  Starting communication with resurrector...OK
                  Detected an Initialized FLASH1 Chip, ID: 0x017E/0x0063 (16MB)
                  Writting FLASH1 memory from 0x000000000000 to 0x000000FFFFFF
                  WARNING: Programming Error (0x25) at 0x000000FE0000 is Ignored.
                  WARNING: Programming Error (0x25) at 0x000000FF0000 is Ignored.
                  Completed in 00:06:56.641 (Average Transfer Rate: 39.32 kB/s)

                  Comment

                  • #10
                    Alcatel C131 Successfully Revived with S183 DLL

                    Code:
                    Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.55
Selected Resurrector: [ZTE S183 V1.0.5162.54298]

Connecting to the dead body...OK
Detected dead body ID: 0x122CE0E1 - IGNORED!
Set I/O Voltage reads as 1.81V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz]
Settings Code: 0x24010009000000000000000001000000

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected an Initialized FLASH1 Chip, ID: 0x017E/0x0063 (16MB)

Writting FLASH1 memory from 0x000000000000 to 0x000000FFFFFF
WARNING: Programming Error (0x25) at 0x000000FE0000 is Ignored.
WARNING: Programming Error (0x25) at 0x000000FF0000 is Ignored.
Completed in 00:10:15.109 (Average Transfer Rate: 26.64 kB/s)

                    Comment

                    • #11
                      Again c131 done

                      Open serial port...OK
                      Connecting to the RIFF Box...OK
                      Firmware Version: 1.37, JTAG Manager Version: 1.55
                      Selected Resurrector: [ZTE S183 V1.0.5162.54298]
                      Connecting to the dead body...OK
                      Detected dead body ID: 0x122CE0E1 - IGNORED!
                      Set I/O Voltage reads as 1.80V, TCK Frequency is RTCK
                      Adaptive Clocking RTCK Sampling is: [Sample at MAX]
                      Settings Code: 0x24010000000000000000000001000000
                      Resurrection sequence started.
                      Establish communication with the phone...OK
                      Initializing internal hardware configuration...OK
                      Uploading resurrector data into memory...OK
                      Starting communication with resurrector...OK
                      Detected an Initialized FLASH1 Chip, ID: 0x017E/0x0063 (16MB)
                      Writting FLASH1 memory from 0x000000000000 to 0x000000FFFFFF
                      ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK
                      ERROR: Timeout while waiting for DCC Loader response. Trying to recover...OK
                      WARNING: Programming Error (0x25) at 0x000000FE0000 is Ignored.
                      WARNING: Programming Error (0x25) at 0x000000FF0000 is Ignored.
                      Completed in 00:05:58.203 (Average Transfer Rate: 45.74 kB/s)

                      Comment

                      • #12
                        Zte c132 ver.b05 16mb done with riff box

                        THANKSS Mr. LEGIJA
                        Open serial port...OK
                        Connecting to the RIFF Box...OK
                        Firmware Version: 1.37, JTAG Manager Version: 1.55
                        Selected Resurrector: [ZTE S183 V1.0.5162.54298]
                        Restarting target (nRST Low then High)...OK

                        Connecting to the dead body...OK
                        Detected dead body ID: 0x122C80E1 - CORRECT!
                        Set I/O Voltage reads as 1.81V, [COLOR=#0000FF !important]TCK Frequency[/COLOR] is RTCK
                        [COLOR=#0000FF !important]Adaptive Clocking RTCK Sampling[/COLOR] is: [Sample at MAX]

                        Resurrection sequence started.
                        Establish communication with the phone...OK
                        Initializing internal [COLOR=#0000FF !important]hardware configuration[/COLOR]...OK
                        Uploading resurrector data into memory...OK
                        Starting communication with resurrector...OK

                        Detected an Initialized FLASH1 Chip, ID: 0x017E/0x0063 (16MB)
                        [COLOR=#0000FF !important]Selected Resurrection Data[/COLOR] for the NOR Chip with IDs: 0x017E/0x0063

                        Flashing the dead body...OK
                        WARNING: Programming Error (0x25) at 0x000000FE0000 is Ignored.
                        WARNING: Programming Error (0x25) at 0x000000FF0000 is Ignored.
                        Resurrection complete!

                        Comment

                        • #13
                          zte s183 16mb with relince not done

                          Resurrection sequence started.
                          Establish communication with the phone...OK
                          Initializing internal hardware configuration...OK
                          Uploading resurrector data into memory...OK
                          Starting communication with resurrector...OK

                          Detected an Initialized FLASH1 Chip, ID: 0x017E/0x0065 (16MB)

                          Writting FLASH1 memory from 0x000000000000 to 0x000000FFFFFF
                          ERROR: Timeout while waiting for DCC Loader response. Trying to recover...FAILED
                          ERROR: Failed due to multiple communication errors. Terminating at 0x000000000000

                          Comment

                          • #14
                            zte s183 reliance not done after resurrector not power on

                            Open serial port...OK
                            Connecting to the RIFF Box...OK
                            Firmware Version: 1.37, JTAG Manager Version: 1.55
                            Selected Resurrector: [ZTE S183 V1.0.5162.54298]


                            Connecting to the dead body...OK
                            Detected dead body ID: 0x122C80E1 - CORRECT!
                            Set I/O Voltage reads as 1.81V, TCK Frequency is RTCK
                            Adaptive Clocking RTCK Sampling is: [Sample at MAX]


                            Resurrection sequence started.
                            Establish communication with the phone...OK
                            Initializing internal hardware configuration...OK
                            Uploading resurrector data into memory...OK
                            Starting communication with resurrector...OK


                            Detected an Initialized FLASH1 Chip, ID: 0x017E/0x0065 (16MB)
                            WARNING: No Data for the current NOR Chip. Selected default Data for the NOR Chip with IDs: 0x017E/0x0063


                            Flashing the dead body...OK
                            WARNING: Programming Error (0x25) at 0x000000000000 is Ignored.
                            WARNING: Programming Error (0x25) at 0x000000010000 is Ignored.
                            Resurrection complete!

                            Comment

                            • #15
                              Originally posted by shoaibansari.
                              zte s183 reliance not done after resurrector not power on

                              Open serial port...OK
                              Connecting to the RIFF Box...OK
                              Firmware Version: 1.37, JTAG Manager Version: 1.55
                              Selected Resurrector: [ZTE S183 V1.0.5162.54298]


                              Connecting to the dead body...OK
                              Detected dead body ID: 0x122C80E1 - CORRECT!
                              Set I/O Voltage reads as 1.81V, TCK Frequency is RTCK
                              Adaptive Clocking RTCK Sampling is: [Sample at MAX]


                              Resurrection sequence started.
                              Establish communication with the phone...OK
                              Initializing internal hardware configuration...OK
                              Uploading resurrector data into memory...OK
                              Starting communication with resurrector...OK


                              Detected an Initialized FLASH1 Chip, ID: 0x017E/0x0065 (16MB)
                              WARNING: No Data for the current NOR Chip. Selected default Data for the NOR Chip with IDs: 0x017E/0x0063


                              Flashing the dead body...OK
                              WARNING: Programming Error (0x25) at 0x000000000000 is Ignored.
                              WARNING: Programming Error (0x25) at 0x000000010000 is Ignored.
                              Resurrection complete!
                              riff team plz. fix this 1........

                              Comment

                              Previous 1 2 template Next
                              Working...
                              X

                              We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.

                              By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.

                              I Agree