Hi,
this is my log with Riff Box v1.
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.53 (RIFFBOX1), JTAG Manager Version: 1.86
Selected Manual Mode: [RJ-45, 2.50 MHz, 1 Bit Bus Width (DAT0), 1.80V]
Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 1.79V, SD_CLK Frequency is 2.50 MHz
Memory Type .......................... SD
Manufacturer ID ...................... 0x1B
OEM/Application ID ................... "SM"
Product Name ......................... "SMI "
Package .............................. Removable
User Area Partition Size ............. 0x00003CA80000 Bytes (970.50 MB)
OCR Register ......................... 0x80FF8000 (High Voltage)
Write Protection Bits ................ NONE
Chip Revision ........................ 1.0
Serial Number ........................ 0x0F690C05
Memory Manufacturing Date ............ June, 2007
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.53 (RIFFBOX1), JTAG Manager Version: 1.86
Selected Manual Mode: [RJ-45, 2.50 MHz, 1 Bit Bus Width (DAT0), 1.80V]
Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 1.78V, SD_CLK Frequency is 2.50 MHz
Detected SD Chip, ID: 0x1B/"SM" (SMI ), User Area Partition = 0x00003CA80000 Bytes (970.50 MB)
Reading "User Area Partition" address space from 0x000000000000 to 0x00003CA7FFFF
ERROR: Read Failed with Error Code: (17:73). Terminating at 0x000000000000
I have this error with all my SD.
All SD I try works fine on pc.
Best regards.
this is my log with Riff Box v1.
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.53 (RIFFBOX1), JTAG Manager Version: 1.86
Selected Manual Mode: [RJ-45, 2.50 MHz, 1 Bit Bus Width (DAT0), 1.80V]
Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 1.79V, SD_CLK Frequency is 2.50 MHz
Memory Type .......................... SD
Manufacturer ID ...................... 0x1B
OEM/Application ID ................... "SM"
Product Name ......................... "SMI "
Package .............................. Removable
User Area Partition Size ............. 0x00003CA80000 Bytes (970.50 MB)
OCR Register ......................... 0x80FF8000 (High Voltage)
Write Protection Bits ................ NONE
Chip Revision ........................ 1.0
Serial Number ........................ 0x0F690C05
Memory Manufacturing Date ............ June, 2007
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.53 (RIFFBOX1), JTAG Manager Version: 1.86
Selected Manual Mode: [RJ-45, 2.50 MHz, 1 Bit Bus Width (DAT0), 1.80V]
Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 1.78V, SD_CLK Frequency is 2.50 MHz
Detected SD Chip, ID: 0x1B/"SM" (SMI ), User Area Partition = 0x00003CA80000 Bytes (970.50 MB)
Reading "User Area Partition" address space from 0x000000000000 to 0x00003CA7FFFF
ERROR: Read Failed with Error Code: (17:73). Terminating at 0x000000000000
I have this error with all my SD.
All SD I try works fine on pc.
Best regards.
Comment