oppo a5s unlock error

[s.jafer]

oppo a5s cph 1909 unlock error and read write error

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.54 (RIFFBOX1), JTAG Manager Version: 1.90
Selected Package: [Oppo A5S CPH1909 RESET V1.06 by <legija>, <RJ-45>, 1 Bit Bus Width (DAT0)]

Connecting to the SD/eMMC Card...OK
WARNING: Embedded I/O Voltage is overriden to 1.80V
Set I/O Voltage reads as 1.79V, SD_CLK Frequency is 2.50 MHz

Memory Identification Info

Memory Type: eMMC
Manufacturer ID: 0x15 (SAMSUNG)
OEM/Application ID: 0x00
Product Name: "QD63MB"
Package: BGA

Memory Capacity and Geometry Info

User Area Partition Size ............. 0x000747C00000 Bytes (29.12 GB)
Boot Partition Size .................. 0x000000400000 Bytes (4.00 MB)
RPMB Partition Size .................. 0x000001000000 Bytes (16.00 MB)
OCR Register ......................... 0xC0FF8080 (Dual Voltage, High Capacity)
CID Register ......................... 150100514436334D42032BBECE63162F
CSD Register ......................... D02701320F5903FFF6DBFFEF8E40400D
Write Protection Bits ................ NONE
ExtCSD Register Fields ............... [177] = 0x02, [179] = 0x48, [162] = 0x01
Boot Configuration ................... Boot from Boot Partition 1 (Bus Width = 8 Bits)
Max Speed Supported .................. 200MHz
Chip Revision ........................ 0.3
Multimedia Card Revision ............. 1.8 (eMMC v5.1)
Serial Number ........................ 0x2BBECE63
Memory Manufacturing Date ............ February, 2019

Memory Health Information

Device life time reflected by Reserved Blocks - NORMAL
Estimated wear out of MLC Memory - Wear out: 30%..40%, Lifetime remaining: 60%..70%
Estimated wear out of SLC Memory - Wear out: 30%..40%, Lifetime remaining: 60%..70%



1/25/2021 1:18:18 PM] Connecting to the SD/eMMC Card...OK
[1/25/2021 1:18:18 PM] WARNING: Embedded I/O Voltage is overriden to 1.80V
[1/25/2021 1:18:18 PM] Set I/O Voltage reads as 1.79V, SD_CLK Frequency is 2.50 MHz
[1/25/2021 1:18:18 PM]
[1/25/2021 1:18:18 PM] Detected eMMC Chip, ID: 0x15/0x00 (QD63MB), User Area Partition = 0x000747C00000 Bytes (29.12 GB)
[1/25/2021 1:18:18 PM]
[1/25/2021 1:18:18 PM] Writting to the SD/MMC Memory...ERROR
[1/25/2021 1:18:18 PM] ERROR: SD/MMC Communication Error = 0x71 (0x00000F) at 0x000004108000. Trying to recover...OK
[1/25/2021 1:18:18 PM] ERROR: SD/MMC Communication Error = 0x74 (0x00001B) at 0x000004108000. Trying to recover...OK
[1/25/2021 1:18:18 PM] ERROR: SD/MMC Communication Error = 0x74 (0x00001B) at 0x000004108000. Trying to recover...OK
[1/25/2021 1:18:18 PM] ERROR: Stopped due to multiple communication errors. Terminating at 0x000004108000
[1/25/2021 1:18:18 PM] [FINISH OPERATION_ID = RESURRECT]

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.54 (RIFFBOX1), JTAG Manager Version: 1.90
Selected Package: [Oppo A5S CPH1909 RESET V1.06 by <legija>, <RJ-45>, 1 Bit Bus Width (DAT0)]

Connecting to the SD/eMMC Card...OK
WARNING: Embedded I/O Voltage is overriden to 1.80V
Set I/O Voltage reads as 1.79V, SD_CLK Frequency is 2.50 MHz

Detected eMMC Chip, ID: 0x15/0x00 (QD63MB), User Area Partition = 0x000747C00000 Bytes (29.12 GB)

Reading "Boot Area Partition 1" address space from 0x000000000000 to 0x0000003FFFFF
ERROR: Read Failed with Error Code: (01:71). Terminating at 0x000000000000

[Legija]

Set VCCQ to 2.2v and clock to 960KHz.

[s.jafer]

first thanks for quick reply vccq fromusp cable from same pc clock speed all i checked but same error

[s.jafer]

ok job done thanks for reply




Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.54 (RIFFBOX1), JTAG Manager Version: 1.90
Selected Package: [Oppo A5S CPH1909 RESET V1.06 by <legija>, <RJ-45>, 1 Bit Bus Width (DAT0)]

Connecting to the SD/eMMC Card...OK
WARNING: Embedded I/O Voltage is overriden to 2.20V
Set I/O Voltage reads as 2.22V, SD_CLK Frequency is 2.50 MHz

Detected eMMC Chip, ID: 0x15/0x00 (QD63MB), User Area Partition = 0x000747C00000 Bytes (29.12 GB)

Writting to the SD/MMC Memory...OK

Package execution complete!