Connecting to the SD/eMMC Card...ERROR (Samsung i9505)

[knoc]

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.51 (RIFFBOX1), JTAG Manager Version: 1.81
Selected Resurrector: [Samsung I9505 (XXUHPK2) ISP V1.0.6693.44320, <RJ-45>, 1 Bit Bus Width (DAT0)]

Connecting to the SD/eMMC Card...ERROR
Set I/O Voltage reads as 1.81V, SD_CLK Frequency is 649 KHz

Connecting to the SD/eMMC Card Failed (ERR[0075], POS[000B])

[Legija]

1. Not connected properly
2. Dead eMMC


You can connect this model via JTAG port, but also USB is supported with free tools.

[knoc]

what do you mean usb is supported with free tools i am trying to do dead boot repair. phone was working then i flashed with odin and never powered on again so i purchased riff to try and do boot repair and actually the first time it worked well and i did resurrection but still phone could not boot when i tried again the next day i started getting error with every phone i connected

[knoc]

i am ussing rj-45 interface not jtag

[knoc]

and i connected the vcc and vccio pins on th riff box pcb to provide voltage to vcc and vccq on phone pcb i am not using battery and usb cable

[Legija]

You should know that Samsung S4 Qualcomm models do have anti rollback protection.
That means it's not possible to flash lower bootloader version then it was flashed last time.


This model can be repaired by JTAG, ISP and USB.


For JTAG connection, You need to connect wires to phone JTAG port.
For ISP connection, You need also pull up resistors if You use V1 box without adapter.


For USB repair, You need QPST latest version and phone to be in 9008 mode (EDL). To force EDL mode, short CMD or DAT0 to GND and connect USB cable to board, without battery. After phone is detected, disconnect shortcut, and run emmcswdownload.


Extract USB Pack archive to any folder, open "Configuration.xml" with txt editor and edit line :

<search_paths>
C:\ProgramData\Qualcomm\QPST\reflash\
</search_paths>

Put there actual path to extracted files.


On eMMCswdownlaod click "Load configuration and start download" and then select "configuration.xml".

[knoc]

the archive for the repair pack is damaged. yes i am using v1 box without adapter

[Legija]

Archive is not damaged, maybe You need to download it again.


Is Your phone detected on USB port now ?

[knoc]

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.51 (RIFFBOX1), JTAG Manager Version: 1.81
Selected Resurrector: [Samsung I8262 V1.0.5053.47547]

Connecting to the dead body...FAILED
None is detected.




i connected working phone but still get this error

[knoc]

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.51 (RIFFBOX1), JTAG Manager Version: 1.81
Selected Resurrector: [Samsung I8262 V1.0.5053.47547]

Connecting to the dead body...ERROR
ERROR: The RTCK Signal does not respond.

[knoc]

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.51 (RIFFBOX1), JTAG Manager Version: 1.81
Selected Resurrector: [Samsung I8262 ISP V1.0.6607.34408, <JTAG>, 1 Bit Bus Width (DAT0)]

Connecting to the SD/eMMC Card...ERROR
Set I/O Voltage reads as 1.80V, SD_CLK Frequency is 1 MHz

Connecting to the SD/eMMC Card Failed (ERR[0075], POS[000B])




even with a working phone that can power on normally

[Legija]

I'm not sure what exactly You're doing here.


This phone supports connection via JTAG and ISP.
For JTAG, phone needs to be connected with battery and usb cable connected to PC.
For ISP, phone must NOT be powered by any source (no battery and no usb cable).


I see that You selected JTAG port of ISP connection, have You built adapter and how did You connected VCC and VCCQ ?


ISP connection can be established via RJ45 port and via JTAG port, but in both cases it needs pullup resistors from VCCQ to CMD and DAT0.

[f-bone]

I am also trying to read same i9505 emmc but also get error. I am using the rj-45 adapter and the dip switch is at ON (100ohm pullups are used)... maybe dead nand? Tried all frequencies. Using USB port of adapter for power (1.8 & 2.9v).

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.54 (RIFFBOX1), JTAG Manager Version: 1.89
Selected Resurrector: [Samsung I9505 (XXUHPK2) ISP V1.0.6693.44320, <RJ-45>, 1 Bit Bus Width (DAT0)]

Connecting to the SD/eMMC Card...ERROR
Set I/O Voltage reads as 1.79V, SD_CLK Frequency is 533 KHz

Connecting to the SD/eMMC Card Failed (ERR[0073], POS[0004])