plz help j100h dead boot rapair

[diganta riff]

hello lagija plz help how to repair j100h dead boot repair step by step--

here is some log

1 Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.49 (RIFFBOX2), JTAG Manager Version: 1.77
Selected Resurrector: [Samsung J100H ISP V1.0.6443.40605]

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 1.79V, SD_CLK Frequency is 6 MHz

Detected eMMC Chip, ID: 0x65/0x6F (M MOR ), User Area Partition = 0x000008000000 Bytes (128.00 MB)

No Resurrection Data is available for the eMMC Chip with Capacity = 131072 KB
WARNING!!! Using Resurrection Data for the eMMC Chip with Capacity = 3.64 GB

Flashing the dead body...
2)Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.49 (RIFFBOX2), JTAG Manager Version: 1.77

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 1.80V, SD_CLK Frequency is 6 MHz

Memory Type .......................... eMMC
Manufacturer ID ...................... 0x65
OEM/Application ID ................... 0x6F
Product Name ......................... "M MOR "
Package .............................. Removable
User Area Partition Size ............. 0x000008000000 Bytes (128.00 MB)
Boot Partition Size .................. 0x000000200000 Bytes (2.00 MB)
RPMB Partition Size .................. 0x000000020000 Bytes (128.00 KB)
OCR Register ......................... 0x80FF8080 (Dual Voltage)
Write Protection Bits ................ NONE
ExtCSD Register Fields ............... [177] = 0x00, [179] = 0x78, [162] = 0x00
Boot Configuration ................... Boot from User Area (Bus Width = 1Bit)
Chip Revision ........................ 8.1
Multimedia Card Revision ............. 1.5 (eMMC v4.41)
Serial Number ........................ 0x00000240
Memory Manufacturing Date ............ January, 2014

[diganta riff]

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.49 (RIFFBOX2), JTAG Manager Version: 1.77

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 2.81V, SD_CLK Frequency is 6 MHz

Memory Type .......................... eMMC
Manufacturer ID ...................... 0x90
OEM/Application ID ................... 0x4A
Product Name ......................... "H4G2b "
Package .............................. BGA
User Area Partition Size ............. 0x0000E9000000 Bytes (3.64 GB)
Boot Partition Size .................. 0x000000400000 Bytes (4.00 MB)
RPMB Partition Size .................. 0x000000400000 Bytes (4.00 MB)
OCR Register ......................... 0xC0FF8080 (Dual Voltage, High Capacity)
Write Protection Bits ................ NONE
ExtCSD Register Fields ............... [177] = 0x00, [179] = 0x08, [162] = 0x00
Boot Configuration ................... Boot from Boot Partition 1 (Bus Width = 1Bit)
Chip Revision ........................ 0.1
Multimedia Card Revision ............. 1.6 (eMMC v4.5, v4.51)
Serial Number ........................ 0x9C148C2C
Memory Manufacturing Date ............ April, 2015

[Legija]

Is this same phone log ? In first log eMMC controller was in panic mode.
You might need to replace eMMC chip, maybe.

[diganta riff]

many successful report others box but your box not any success

[Legija]

Detected eMMC Chip, ID: 0x65/0x6F (M MOR ), User Area Partition = 0x000008000000 Bytes (128.00 MB)

This is sign that something is wrong with eMMC, because it shows default size, shown by controller in panic mode.

Before jumping to conclusion You should first use logic and think about possible reasons for this to happen, e.g. cold soldering under emmc or insufficient power.

How did phone died and how did you connected it exactly ?

[pachicoo]

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.49 (RIFFBOX1), JTAG Manager Version: 1.76

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 2.79V, SD_CLK Frequency is 649 KHz

Memory Type .......................... eMMC
Manufacturer ID ...................... 0x90
OEM/Application ID ................... 0x4A
Product Name ......................... "H4G2b "
Package .............................. BGA
User Area Partition Size ............. 0x0000E9000000 Bytes (3.64 GB)
Boot Partition Size .................. 0x000000400000 Bytes (4.00 MB)
RPMB Partition Size .................. 0x000000400000 Bytes (4.00 MB)
OCR Register ......................... 0xC0FF8080 (Dual Voltage, High Capacity)
Write Protection Bits ................ NONE
ExtCSD Register Fields ............... [177] = 0x00, [179] = 0x08, [162] = 0x00
Boot Configuration ................... Boot from Boot Partition 1 (Bus Width = 1Bit)
Chip Revision ........................ 0.1
Multimedia Card Revision ............. 1.6 (eMMC v4.5, v4.51)
Serial Number ........................ 0xC517BA32
Memory Manufacturing Date ............ June, 2015

same problem here need help

giving this error
pen serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.49 (RIFFBOX1), JTAG Manager Version: 1.76

Connecting to the SD/eMMC Card...ERROR
Set I/O Voltage reads as 2.79V, SD_CLK Frequency is 828 KHz

Connecting to the SD/eMMC Card Failed (ERR[0070], POS[0002])

[Legija]

Start with VCCIO set to 1.8 and increase in small steps - e.g. 2.0, 2.2 etc.
I think 2.8 could be too much.