riff 1.62 emmc kingston read partition failed, help me legija...

[real cell]

Connecting to the RIFF Box...OK
Firmware Version: 1.39 (RIFFBOX1), JTAG Manager Version: 1.62

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 1.81V, SD_CLK Frequency is 960 KHz

Memory Type .......................... eMMC
Manufacturer ID ...................... 0x06
OEM/Application ID ................... 0x00
Product Name ......................... "16 "
Package .............................. Removable
User Area Partition Size ............. 0x0001D5400000 Bytes (7.33 GB)
Boot Partition Size .................. 0x000000200000 Bytes (2.00 MB)
RPMB Partition Size .................. 0x000000020000 Bytes (128.00 KB)
OCR Register ......................... 0xC0FF8080 (Dual Voltage, High Capacity)
Write Protection Bits ................ NONE
Boot Configuration ................... Boot from Boot Partition 1 (Bus Width = 1Bit)
Chip Revision ........................ 15.15
Multimedia Card Revision ............. 1.6 (eMMC v4.5, v4.51)
Serial Number ........................ 0x195C4939
Memory Manufacturing Date ............ April, 2017



Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.39 (RIFFBOX1), JTAG Manager Version: 1.62

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 1.81V, SD_CLK Frequency is 960 KHz

Detected eMMC Chip, ID: 0x06/0x00 (16 ), User Area Partition = 0x0001D5400000 Bytes (7.33 GB)


WARNING: Resuming interrupted read from 0x000000000000, yet to read - 0x000000100000...
Reading "Boot Area Partition 1" address space from 0x000000000000 to 0x0000000FFFFF
Failed to receive answer to READ command.

[Legija]

Hi,
Any idea about phone status? (Dead, working . . .)
Can You try reading boot partition, or extended information from emmc ?
In any case You should check connection and try various clock speeds.

[real cell]

phone status is stuck logo...
yes i try reading from information emmc but eror

[Legija]

1. Have You connected it directly on board (ISP) or via chip adaptor ?
2. If You used ISP, have You installed pull-up resistors ?
3. Have You tried to lower down clock speed ?

[Tedjo]

Connecting to the RIFF Box...OK
Firmware Version: 1.39 (RIFFBOX1), JTAG Manager Version: 1.62

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 1.81V, SD_CLK Frequency is 960 KHz

Memory Type .......................... eMMC
Manufacturer ID ...................... 0x06
OEM/Application ID ................... 0x00
Product Name ......................... "16 "
Package .............................. Removable
User Area Partition Size ............. 0x0001D5400000 Bytes (7.33 GB)
Boot Partition Size .................. 0x000000200000 Bytes (2.00 MB)
RPMB Partition Size .................. 0x000000020000 Bytes (128.00 KB)
OCR Register ......................... 0xC0FF8080 (Dual Voltage, High Capacity)
Write Protection Bits ................ NONE
Boot Configuration ................... Boot from Boot Partition 1 (Bus Width = 1Bit)
Chip Revision ........................ 15.15
Multimedia Card Revision ............. 1.6 (eMMC v4.5, v4.51)
Serial Number ........................ 0x195C4939
Memory Manufacturing Date ............ April, 2017



Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.39 (RIFFBOX1), JTAG Manager Version: 1.62

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 1.81V, SD_CLK Frequency is 960 KHz

Detected eMMC Chip, ID: 0x06/0x00 (16 ), User Area Partition = 0x0001D5400000 Bytes (7.33 GB)


WARNING: Resuming interrupted read from 0x000000000000, yet to read - 0x000000100000...
Reading "Boot Area Partition 1" address space from 0x000000000000 to 0x0000000FFFFF
Failed to receive answer to READ command.

Hi ... where did you download v1.62 jtag manager ??
want to upgrade it too ...
but i can not find it, even via "check for update" button ..

[mtk6572s4clone]

Hi ... where did you download v1.62 jtag manager ??
want to upgrade it too ...
but i can not find it, even via "check for update" button ..

Unlock Forum - RIFF Box support forum

greetings

[Tedjo]

Unlock Forum - RIFF Box support forum

greetings

I can not access the link

here is the error message

Tedjo, you do not have permission to access this page. This could be due to one of several reasons:

Your user account may not have sufficient privileges to access this page. Are you trying to edit someone else's post, access administrative features or some other privileged system?
If you are trying to post, the administrator may have disabled your account, or it may be awaiting activation.

[mtk6572s4clone]

I can not access the link

here is the error message

Tedjo, you do not have permission to access this page. This could be due to one of several reasons:

Your user account may not have sufficient privileges to access this page. Are you trying to edit someone else's post, access administrative features or some other privileged system?
If you are trying to post, the administrator may have disabled your account, or it may be awaiting activation.

Replied on PM, greetings.

[real cell]

1. Have You connected it directly on board (ISP) or via chip adaptor ?
2. If You used ISP, have You installed pull-up resistors ?
3. Have You tried to lower down clock speed ?

i used via chip adaptor, i tried with lower clock low speed stil same eror

[nicolayer]

Memory Type .......................... eMMC
Manufacturer ID ...................... 0x06
OEM/Application ID ................... 0x00
Product Name ......................... "16 "
Package .............................. Removable
User Area Partition Size ............. 0x0001D5400000 Bytes (7.33 GB)
Boot Partition Size .................. 0x000000200000 Bytes (2.00 MB)
RPMB Partition Size .................. 0x000000020000 Bytes (128.00 KB)
OCR Register ......................... 0xC0FF8080 (Dual Voltage, High Capacity)
Write Protection Bits ................ NONE
Boot Configuration ................... Boot from Boot Partition 1 (Bus Width = 1Bit)
Chip Revision ........................ 15.15
Multimedia Card Revision ............. 1.6 (eMMC v4.5, v4.51)
Serial Number ........................ 0x195C4939
Memory Manufacturing Date ............ April, 2017

Red marked info is not normal, possible 2 cases:
- dead emmc,
- bug in 1.62.

did you try check emmc with manager 1.61?

[real cell]

thanks....problem solved

emmc dead

[vainer12]

Solved