Hi!
I was trying to recover a phone that has a bad sbl1 and sbl2 partitions (I know because it got bricked after a dd command on these).
tried the s7390 ressurector:
[1/26/2018 10:20:15] [START OPERATION_ID = RESURRECT]
[1/26/2018 10:21:02] Open serial port...OK
[1/26/2018 10:21:02] Connecting to the RIFF Box...OK
[1/26/2018 10:21:02] Firmware Version: 1.49 (RIFFBOX1), JTAG Manager Version: 1.76
[1/26/2018 10:21:02] Selected Resurrector: [Samsung S7390 V1.0.5280.12260]
[1/26/2018 10:21:02]
[1/26/2018 10:21:02] Connecting to the dead body...OK
[1/26/2018 10:21:02] Detected dead body ID: 0x4BA00477 - CORRECT!
[1/26/2018 10:21:02] Set I/O Voltage reads as 1.81V, TCK Frequency is 8 MHz
[1/26/2018 10:21:02]
[1/26/2018 10:21:02] Resurrection sequence started.
[1/26/2018 10:21:02] Establish communication with the phone...OK
[1/26/2018 10:21:02] Initializing internal hardware configuration...OK
[1/26/2018 10:21:02] Uploading resurrector data into memory...OK
[1/26/2018 10:21:02] Starting communication with resurrector...OK
[1/26/2018 10:21:02]
[1/26/2018 10:21:02] Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0100 (N5U00M, 0x0000E9000000 Bytes = 3.64 GB)
[1/26/2018 10:21:02] Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0100 (N5U00M, 0x000000200000 Bytes = 2.00 MB)
[1/26/2018 10:21:02]
[1/26/2018 10:21:02] Selected Resurrection Data for the eMMC Chip with Capacity = 3.64GB
[1/26/2018 10:21:02]
[1/26/2018 10:21:02] Flashing the dead body...OK
[1/26/2018 10:21:02] Resurrection complete!
[1/26/2018 10:21:02] [FINISH OPERATION_ID = RESURRECT]
apparently everything got ok, but phone was still dead, so tried again:
[1/26/2018 10:49:00] [START OPERATION_ID = RESURRECT]
[1/26/2018 10:49:02] Open serial port...OK
[1/26/2018 10:49:02] Connecting to the RIFF Box...OK
[1/26/2018 10:49:02] Firmware Version: 1.49 (RIFFBOX1), JTAG Manager Version: 1.76
[1/26/2018 10:49:02] Selected Resurrector: [Samsung S7390 V1.0.5280.12260]
[1/26/2018 10:49:02]
[1/26/2018 10:49:02] Connecting to the dead body...OK
[1/26/2018 10:49:02] Detected dead body ID: 0x4BA00477 - CORRECT!
[1/26/2018 10:49:02] Set I/O Voltage reads as 1.83V, TCK Frequency is 8 MHz
[1/26/2018 10:49:02]
[1/26/2018 10:49:02] Resurrection sequence started.
[1/26/2018 10:49:02] Establish communication with the phone...OK
[1/26/2018 10:49:02] Initializing internal hardware configuration...FAILED
[1/26/2018 10:49:02] ERROR: Wrong response code from the RIFF Box: 0x81
[1/26/2018 10:49:02] [FINISH OPERATION_ID = RESURRECT]
and now I can't initialize the hardware doesn't matter what, always return this 0x81 error even when trying dcc access.
what does this error means?
I was trying to recover a phone that has a bad sbl1 and sbl2 partitions (I know because it got bricked after a dd command on these).
tried the s7390 ressurector:
[1/26/2018 10:20:15] [START OPERATION_ID = RESURRECT]
[1/26/2018 10:21:02] Open serial port...OK
[1/26/2018 10:21:02] Connecting to the RIFF Box...OK
[1/26/2018 10:21:02] Firmware Version: 1.49 (RIFFBOX1), JTAG Manager Version: 1.76
[1/26/2018 10:21:02] Selected Resurrector: [Samsung S7390 V1.0.5280.12260]
[1/26/2018 10:21:02]
[1/26/2018 10:21:02] Connecting to the dead body...OK
[1/26/2018 10:21:02] Detected dead body ID: 0x4BA00477 - CORRECT!
[1/26/2018 10:21:02] Set I/O Voltage reads as 1.81V, TCK Frequency is 8 MHz
[1/26/2018 10:21:02]
[1/26/2018 10:21:02] Resurrection sequence started.
[1/26/2018 10:21:02] Establish communication with the phone...OK
[1/26/2018 10:21:02] Initializing internal hardware configuration...OK
[1/26/2018 10:21:02] Uploading resurrector data into memory...OK
[1/26/2018 10:21:02] Starting communication with resurrector...OK
[1/26/2018 10:21:02]
[1/26/2018 10:21:02] Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0100 (N5U00M, 0x0000E9000000 Bytes = 3.64 GB)
[1/26/2018 10:21:02] Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0100 (N5U00M, 0x000000200000 Bytes = 2.00 MB)
[1/26/2018 10:21:02]
[1/26/2018 10:21:02] Selected Resurrection Data for the eMMC Chip with Capacity = 3.64GB
[1/26/2018 10:21:02]
[1/26/2018 10:21:02] Flashing the dead body...OK
[1/26/2018 10:21:02] Resurrection complete!
[1/26/2018 10:21:02] [FINISH OPERATION_ID = RESURRECT]
apparently everything got ok, but phone was still dead, so tried again:
[1/26/2018 10:49:00] [START OPERATION_ID = RESURRECT]
[1/26/2018 10:49:02] Open serial port...OK
[1/26/2018 10:49:02] Connecting to the RIFF Box...OK
[1/26/2018 10:49:02] Firmware Version: 1.49 (RIFFBOX1), JTAG Manager Version: 1.76
[1/26/2018 10:49:02] Selected Resurrector: [Samsung S7390 V1.0.5280.12260]
[1/26/2018 10:49:02]
[1/26/2018 10:49:02] Connecting to the dead body...OK
[1/26/2018 10:49:02] Detected dead body ID: 0x4BA00477 - CORRECT!
[1/26/2018 10:49:02] Set I/O Voltage reads as 1.83V, TCK Frequency is 8 MHz
[1/26/2018 10:49:02]
[1/26/2018 10:49:02] Resurrection sequence started.
[1/26/2018 10:49:02] Establish communication with the phone...OK
[1/26/2018 10:49:02] Initializing internal hardware configuration...FAILED
[1/26/2018 10:49:02] ERROR: Wrong response code from the RIFF Box: 0x81
[1/26/2018 10:49:02] [FINISH OPERATION_ID = RESURRECT]
and now I can't initialize the hardware doesn't matter what, always return this 0x81 error even when trying dcc access.
what does this error means?
Comment