G316HU Dead after flash G313H. How to solve?

[.::JYOTIRMAY::.]

Sir a received set dead condition. Resurrect by RJ-45. Resurrection successfull but still dead.


Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.51 (RIFFBOX1), JTAG Manager Version: 1.86
Selected Resurrector: [Samsung G316HU ISP V1.0.6724.49539, <RJ-45>, 1 Bit Bus Width (DAT0)]

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 2.75V, SD_CLK Frequency is 649 KHz

Memory Type .......................... eMMC
Manufacturer ID ...................... 0x90
OEM/Application ID ................... 0x4A
Product Name ......................... "H4G2b "
Package .............................. BGA
User Area Partition Size ............. 0x0000E9000000 Bytes (3.64 GB)
Boot Partition Size .................. 0x000000400000 Bytes (4.00 MB)
RPMB Partition Size .................. 0x000000400000 Bytes (4.00 MB)
OCR Register ......................... 0xC0FF8080 (Dual Voltage, High Capacity)
Write Protection Bits ................ NONE
ExtCSD Register Fields ............... [177] = 0x00, [179] = 0x08, [162] = 0x00
Boot Configuration ................... Boot from Boot Partition 1 (Bus Width = 1 Bit)
Chip Revision ........................ 0.1
Multimedia Card Revision ............. 1.6 (eMMC v4.5, v4.51)
Serial Number ........................ 0x02DBB989
Memory Manufacturing Date ............ December, 2014



Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.51 (RIFFBOX1), JTAG Manager Version: 1.86
Selected Resurrector: [Samsung G316HU ISP V1.0.6724.49539, <RJ-45>, 1 Bit Bus Width (DAT0)]

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 2.79V, SD_CLK Frequency is 649 KHz

Detected eMMC Chip, ID: 0x90/0x4A (H4G2b ), User Area Partition = 0x0000E9000000 Bytes (3.64 GB)

Selected Resurrection Data for the eMMC Chip with Capacity = 3.64 GB

Flashing the dead body...OK
Resurrection complete!

Any possibilities to repair this one? Thanks in advance.

[Legija]

Dead how ? Blinking or no download mode at all ?

[.::JYOTIRMAY::.]

Dead how ? Blinking or no download mode at all ?

Thanks SIR for reply. Dead means no download mode no blink. After press "VOL+ - " entering cable computer recognize as spreadtrum SCI USB2 Serial port.

[Legija]

Ok i will check what can be done, and upload repair pack here later today.

[Legija]

Save file to repairpacks folder, restart JM, install license and select Samung G316HU OJV0APC1.


Tick all and wait for operation to finish.
If phone doesn't enter DL mode, try with JIG, otherwise emmc could be bad.
In that case read back 128mb from user area partition and upload here, need to check inside.

[.::JYOTIRMAY::.]

Save file to repairpacks folder, restart JM, install license and select Samung G316HU OJV0APC1.


Tick all and wait for operation to finish.
If phone doesn't enter DL mode, try with JIG, otherwise emmc could be bad.
In that case read back 128mb from user area partition and upload here, need to check inside.

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.51 (RIFFBOX1), JTAG Manager Version: 1.86
Selected Package: [Samsung G316HU OJV0APC1 V1.00 by <legija>, <RJ-45>, 1 Bit Bus Width (DAT0)]

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 2.35V, SD_CLK Frequency is 960 KHz

Detected eMMC Chip, ID: 0x90/0x4A (H4G2b ), User Area Partition = 0x0000E9000000 Bytes (3.64 GB)

Writting to the SD/MMC Card...OK
Package execution complete!

Still not entering download mode. Also try with jig.


Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.51 (RIFFBOX1), JTAG Manager Version: 1.86
Selected Package: [Samsung G316HU OJV0APC1 V1.00 by <legija>, <RJ-45>, 1 Bit Bus Width (DAT0)]

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 2.38V, SD_CLK Frequency is 960 KHz

Detected eMMC Chip, ID: 0x90/0x4A (H4G2b ), User Area Partition = 0x0000E9000000 Bytes (3.64 GB)

Reading "User Area Partition" address space from 0x000000000000 to 0x000007FFFFFF
Completed in 00:19:45.499 (Average Transfer Rate: 110.56 kB/s)

Please wait, saving data...OK
Saved to File: C:\Users\JYOTI\Desktop\USER AREA PARTITION 128MB.bin
Completed in 00:00:07.597 (Average Transfer Rate: 16.85 MB/s)


Just a moment...

[Legija]

Ok, as suspected, emmc bad in read only state.
Needs replacement.

[sajon]

Ok, as suspected, emmc bad in read only state.
Needs replacement.

sir how can chek 128mb file to use plugin

[ZameerAhmed]

try one more BL File

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.51 (RIFFBOX1), JTAG Manager Version: 1.86
Selected Package: [Samsung G316HU OJV0APC1 V1.00 by <legija>, <RJ-45>, 1 Bit Bus Width (DAT0)]

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 2.35V, SD_CLK Frequency is 960 KHz

Detected eMMC Chip, ID: 0x90/0x4A (H4G2b ), User Area Partition = 0x0000E9000000 Bytes (3.64 GB)

Writting to the SD/MMC Card...OK
Package execution complete!

Still not entering download mode. Also try with jig.


Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.51 (RIFFBOX1), JTAG Manager Version: 1.86
Selected Package: [Samsung G316HU OJV0APC1 V1.00 by <legija>, <RJ-45>, 1 Bit Bus Width (DAT0)]

Connecting to the SD/eMMC Card...OK
Set I/O Voltage reads as 2.38V, SD_CLK Frequency is 960 KHz

Detected eMMC Chip, ID: 0x90/0x4A (H4G2b ), User Area Partition = 0x0000E9000000 Bytes (3.64 GB)

Reading "User Area Partition" address space from 0x000000000000 to 0x000007FFFFFF
Completed in 00:19:45.499 (Average Transfer Rate: 110.56 kB/s)

Please wait, saving data...OK
Saved to File: C:\Users\JYOTI\Desktop\USER AREA PARTITION 128MB.bin
Completed in 00:00:07.597 (Average Transfer Rate: 16.85 MB/s)


Just a moment...

try This BL File ..................................................

[Legija]

sir how can chek 128mb file to use plugin

Open dump in plugin, click parse local dump file, click check for blank.