My Riff box suddenly does not work for both jtag & emmc please help

[karabzn]

good morning sir

this is my problem

jtag. (analyze jtag chain):

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.50 (RIFFBOX1), JTAG Manager Version: 1.80
Selected Resurrector: [Samsung I9505 V1.0.5194.48172]

Connecting to the target...OK
Set I/O Voltage reads as 1.80V, TCK Frequency is RTCK

Following devices are found on the JTAG chain:
Device on TAP #0: ID = 0x4F1F0F0F, IR Length = 0x04 bits
Device on TAP #1: ID = 0x2071B0E1, IR Length = 0x0B bits
Total IR length: 0x000F bits

Analizing IDCODE(s) of the JTAG scan chain:
1. 0x2071B0E1: Qualcomm APQ8064T, H/W Rev. #2

Jtag: when i try to ressurect:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.50 (RIFFBOX1), JTAG Manager Version: 1.80
Selected Resurrector: [Samsung I9505 V1.0.5194.48172]

Connecting to the dead body...FAILED
None is detected.


Emmc SD card read:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.50 (RIFFBOX1), JTAG Manager Version: 1.80

Connecting to the SD/eMMC Card...ERROR
Set I/O Voltage reads as 3.28V, SD_CLK Frequency is 800 KHz

Connecting to the SD/eMMC Card Failed (ERR[0071], POS[0000])

OS: Windows 10 64bit

but with medusa pro everything is fine.


PLease assist me in this regard

Thank you

[otherboy123]

Disable driver signatures

Sent from my MI 6 using Tapatalk

[Legija]

good morning sir

this is my problem

jtag. (analyze jtag chain):

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.50 (RIFFBOX1), JTAG Manager Version: 1.80
Selected Resurrector: [Samsung I9505 V1.0.5194.48172]

Connecting to the target...OK
Set I/O Voltage reads as 1.80V, TCK Frequency is RTCK

Following devices are found on the JTAG chain:
Device on TAP #0: ID = 0x4F1F0F0F, IR Length = 0x04 bits
Device on TAP #1: ID = 0x2071B0E1, IR Length = 0x0B bits
Total IR length: 0x000F bits

Analizing IDCODE(s) of the JTAG scan chain:
1. 0x2071B0E1: Qualcomm APQ8064T, H/W Rev. #2

Jtag: when i try to ressurect:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.50 (RIFFBOX1), JTAG Manager Version: 1.80
Selected Resurrector: [Samsung I9505 V1.0.5194.48172]

Connecting to the dead body...FAILED
None is detected.

Either RTCK pin not connected, or phone battery is empty. If phone SBL1 is erased, battery must be fully charged to work with RIFF DCC loader HW Init script.

Emmc SD card read:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.50 (RIFFBOX1), JTAG Manager Version: 1.80

Connecting to the SD/eMMC Card...ERROR
Set I/O Voltage reads as 3.28V, SD_CLK Frequency is 800 KHz

Connecting to the SD/eMMC Card Failed (ERR[0071], POS[0000])


Thank you

Not enough information to see whats wrong here.

[karabzn]

Ok Sir Thank you for your prompt response