Ok, so far connection seems to be working, NRST works as it should too.
Now switch back to resurrector and on DCC tab click "Read".
Now switch back to resurrector and on DCC tab click "Read".
[11/1/2017 6:37:38 AM] [START OPERATION_ID = RESET_TARGET] [11/1/2017 6:37:38 AM] Open serial port...OK [11/1/2017 6:37:38 AM] Connecting to the RIFF Box...OK [11/1/2017 6:37:38 AM] Firmware Version: 1.47 (RIFFBOX2), JTAG Manager Version: 1.73 [11/1/2017 6:37:38 AM] Selected Resurrector: [Samsung I917 V1.0.4466.60929] [11/1/2017 6:37:38 AM] [11/1/2017 6:37:38 AM] Resetting target...OK [11/1/2017 6:37:38 AM] STATUS: Target is halted. [11/1/2017 6:37:38 AM] [11/1/2017 6:37:38 AM] R0 = 0x00000000 R6 = 0x00000000 R12 = 0x00000000 [11/1/2017 6:37:38 AM] R1 = 0xFFFF4C1C R7 = 0x00000000 R13 = 0xC003BF3C [11/1/2017 6:37:38 AM] R2 = 0x00000000 R8 = 0x00000000 R14 = 0xFFFF4C80 [11/1/2017 6:37:38 AM] R3 = 0x00000000 R9 = 0x00000000 R15 = 0xFFFF117C [11/1/2017 6:37:38 AM] R4 = 0xC003BF64 R10 = 0x00000001 CPSR = 0x600000D3 [11/1/2017 6:37:38 AM] R5 = 0xC0035D80 R11 = 0x00000000 [11/1/2017 6:37:38 AM] [FINISH OPERATION_ID = RESET_TARGET] [11/1/2017 6:37:43 AM] [START OPERATION_ID = DCC_READ_MEMORY] [11/1/2017 6:37:43 AM] [11/1/2017 6:37:43 AM] Current Settings: [11/1/2017 6:37:43 AM] ----------------- [11/1/2017 6:37:43 AM] Address: 000000000000 [11/1/2017 6:37:43 AM] Length: 000000000000 [11/1/2017 6:37:43 AM] Address Space: ROM1 [11/1/2017 6:37:43 AM] AutoFullFlash: CHECKED [11/1/2017 6:37:43 AM] Use End Address: UNCHECKED [11/1/2017 6:37:43 AM] ECC Module Enabled: UNCHECKED [11/1/2017 6:37:43 AM] Image File is Used: CHECKED [11/1/2017 6:37:43 AM] Use Address as Offset: UNCHECKED [11/1/2017 6:37:43 AM] Main (CHECKED): [11/1/2017 6:37:43 AM] Redu (UNCHECKED): [11/1/2017 6:37:43 AM] [11/1/2017 6:37:44 AM] Open serial port...OK [11/1/2017 6:37:44 AM] Connecting to the RIFF Box...OK [11/1/2017 6:37:44 AM] Firmware Version: 1.47 (RIFFBOX2), JTAG Manager Version: 1.73 [11/1/2017 6:37:44 AM] Selected Resurrector: [Samsung I917 V1.0.4466.60929] [11/1/2017 6:37:44 AM] [11/1/2017 6:37:44 AM] Connecting to the dead body...OK [11/1/2017 6:37:44 AM] Detected dead body ID: 0x202400E1 - IGNORED! [11/1/2017 6:37:44 AM] Set I/O Voltage reads as 2.99V, TCK Frequency is RTCK [11/1/2017 6:37:44 AM] Adaptive Clocking RTCK Sampling is: [Sample at 1 MHz] [11/1/2017 6:37:44 AM] Settings Code: 0x25010009000000000000000000000000 [11/1/2017 6:37:44 AM] [11/1/2017 6:37:44 AM] Resurrection sequence started. [11/1/2017 6:37:44 AM] Establish communication with the phone...OK [11/1/2017 6:37:44 AM] Initializing internal hardware configuration...OK [11/1/2017 6:37:44 AM] Uploading resurrector data into memory...OK [11/1/2017 6:37:44 AM] Starting communication with resurrector...FAILED [11/1/2017 6:37:44 AM] ERROR: Wrong DCC data checksum. [11/1/2017 6:37:44 AM] [FINISH OPERATION_ID = DCC_READ_MEMORY]
We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.
By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.
Comment