WHERE TO BUY USB CABLE OF SAGEM my210x,my220v,my411c?

[Eagle7]

Can someone help me to buy one pce of usb unlocking cable of SAGEM my210x,my220v,my411c,etc ,i want to use my Rocker Dongle,please?

[.:ramtelecom:.]

My220v Is not supported Yet By Any tool.

For My210x You Must Solder Tx, Rx and Gnd on Phone Mainboard. Or You can use this adapter : http://www.ipmart.com/main/product/TP,Sagem,MY210X,,215X,Adapter,With,SWITCH,34392.ph p?in=592&find=210x&prod=34392

For My411 you can order the cable from here : http://www.ipmart.com/main/product/Cable,for,Sagem,202C,,700X,,411X,SecCode,33409.php ?in=592&find=Sagem%20Cable&prod=33409

[BFJK04]

My220v Is not supported Yet By Any tool.

For My210x You Must Solder Tx, Rx and Gnd on Phone Mainboard. Or You can use this adapter : http://www.ipmart.com/main/product/TP,Sagem,MY210X,,215X,Adapter,With,SWITCH,34392.ph p?in=592&find=210x&prod=34392

For My411 you can order the cable from here : http://www.ipmart.com/main/product/Cable,for,Sagem,202C,,700X,,411X,SecCode,33409.php ?in=592&find=Sagem%20Cable&prod=33409
Hello Ramtelekom.
I have already bought 2 pieces of this Testpoint Adaptors but have never been able to use any of them!
I have tried with both Rocker Dongle and SagDD + JTag Unlocker Versions 7,1;7,3 and latest 7,5 but all to no avail! I tried to unlock 3 pieces of Sagem My 210x but only 1 piece gave me some information from the phone,hinting that PHONE IS UNKNOWN!
For the rest,I always get : Either Bootloader Failed or Failed to read Imei.
I am getting disappointed.
Can you please direct me as to how to go about the whole process of using this My 210x Testpoint Adadtor?What is the purpose of that red Switch?
NB:
I connect the specially delivered RJ45 cable ,from SagDD to the Adaptor mounted on the phone's PCB Board, set the phone's speed at different levels and tick unlock box and press Do The Job.

[.:ramtelecom:.]

Hello Ramtelekom.
I have already bought 2 pieces of this Testpoint Adaptors but have never been able to use any of them!
I have tried with both Rocker Dongle and SagDD + JTag Unlocker Versions 7,1;7,3 and latest 7,5 but all to no avail! I tried to unlock 3 pieces of Sagem My 210x but only 1 piece gave me some information from the phone,hinting that PHONE IS UNKNOWN!
For the rest,I always get : Either Bootloader Failed or Failed to read Imei.
I am getting disappointed.
Can you please direct me as to how to go about the whole process of using this My 210x Testpoint Adadtor?What is the purpose of that red Switch?
NB:
I connect the specially delivered RJ45 cable ,from SagDD to the Adaptor mounted on the phone's PCB Board, set the phone's speed at different levels and tick unlock box and press Do The Job.
Wrong! The adaptor must be connected to FTDi Interface, Not SagDD Box.
Select Port Com Number and Do unlock ;)

[BFJK04]

Wrong! The adaptor must be connected to FTDi Interface, Not SagDD Box.
Select Port Com Number and Do unlock ;)
Hello,ramtelecom,
can you be a bit specific about this FTDi Interface? I bought this Adaptor together with the specially designed cable meant for SagDD box.I don't know how to connect this Adaptor with this Cable to the FTDi Interface. Please be kind enough to throw more light on this connection.
Thank you very much in advance.
BFJK04.

[.:ramtelecom:.]

Hello,ramtelecom,
can you be a bit specific about this FTDi Interface? I bought this Adaptor together with the specially designed cable meant for SagDD box.I don't know how to connect this Adaptor with this Cable to the FTDi Interface. Please be kind enough to throw more light on this connection.
Thank you very much in advance.
BFJK04.
Cable Must Be connected to an universal Box (infinity, FG , Vygis .... )
Read SagDD user manual it will be clear for you .

[BFJK04]

Hello Ramtelecom,
I have followed your guidelines but still,no success.Today,I connected the special cable that came with the Adaptor to my Infinity box that was plugged into the USB of my computer and connected the other end to the Adaptor that was placed over the phone's PCB.
I logged in on the server and chose the necessary Com Port Number for the Infinity Box.
I ticked UNLOCK Box and hit DO THE JOB Button:the light on the Infinity Box lit green and Software said I should remove and insert Battery and power on the phone.
The problem is while the Adaptor is attached to the phone's PCB if I try to attach the battery,the computer just hangs and the computer finally shuts down.
What I have realised is that when I press the red switch on the Adaptor,it either lights or shuts off the phone,but the Infinity Box cannot boot the phone.What purpose then is the RED SWITCH?
So Please,help me.
Thank You very much in advance.
BFJK04.

[.:ramtelecom:.]

Hello Ramtelecom,
I have followed your guidelines but still,no success.Today,I connected the special cable that came with the Adaptor to my Infinity box that was plugged into the USB of my computer and connected the other end to the Adaptor that was placed over the phone's PCB.
I logged in on the server and chose the necessary Com Port Number for the Infinity Box.
I ticked UNLOCK Box and hit DO THE JOB Button:the light on the Infinity Box lit green and Software said I should remove and insert Battery and power on the phone.
The problem is while the Adaptor is attached to the phone's PCB if I try to attach the battery,the computer just hangs and the computer finally shuts down.
What I have realised is that when I press the red switch on the Adaptor,it either lights or shuts off the phone,but the Infinity Box cannot boot the phone.What purpose then is the RED SWITCH?
So Please,help me.
Thank You very much in advance.
BFJK04.
i have no idea where the problem comes, maybe the TP cable is faulty.
Try to solder Tx, Rx and GND on the phone mainboard and try to unlock it.

[BFJK04]

i have no idea where the problem comes, maybe the TP cable is faulty.
Try to solder Tx, Rx and GND on the phone mainboard and try to unlock it.

Hello Ramtelekom,
Thanks a lot for your efforts.Happily, I have managed to unlock the Sagem My210X phone with the same Testpoint Adaptor and the USB-COM Cable.
This is how I did it:
I connected Rocker Dongle Box to the PC(because I used its serial number to buy the SagDD Credits).I then connected the USB-COM Cable to the Computer USB Port and its RJ45 end to the Testpoint Adaptor and placed the Adaptor on the Telephone's PCB.I logged in on the SAGDD Server and chose the Com Port number for the USB-COM Cable.I didn't connect anything to the Rocker Dongle and I didn't insert any battery into the Phone.
I then pressed the DO THE JOB button and as soon as the progress bar started,I pressed the RED SWITCH on the ADAPTOR and SOFTWARE began to analyze the Phone and finally gave me the Unlock Code!
My other problem is this: I want to unlock some Sagem My100x,but it seems there is no SWITCH on the Testpoint Adaptor:does it mean that I have to attach BATTERY or what? OR can anybody give me the procedure?
Thanks a lot in advance.
BFJK04.:boxing_smiley:

[.:ramtelecom:.]

Hello Ramtelekom,
......
My other problem is this: I want to unlock some Sagem My100x,but it seems there is no SWITCH on the Testpoint Adaptor:does it mean that I have to attach BATTERY or what? OR can anybody give me the procedure?
Thanks a lot in advance.
BFJK04.:boxing_smiley:
happy for you :)

for the other problem, you have two case:

1. Your my100x is a M62 Based Phone :
In this case, you can't do it by rocker, you need SagDD box and TP adaptor and you can do it without credit.

2. Your My100x is a M63/M64 Based Phone:
In this case, you don't need a TP adaptor, Just Use USB TO COM cable without opening the phone.